no keyboard on user now

[glpnet1]

I have no keyboard on my user account now. only in root account.
it started with my x wouldn't keep the proper setting and when I went to check the xorg.conf it had 4 or 5 backups. I deleted all of them and ran Envy again and had to remove th nvidia drivers and reinstall them. Did that 4 time and it works now but the keyboard issue now.
I even copied an xorg.conf from another debian install and that didnt work either.
It works with other distros so I know the keyboard is good.

[Husse]

Thats bad - running as root is not recommended
Post your xorg.conf
You should have something like this

Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "se"
EndSection

You'll probably have another layout
Then you should have something like this

Section "ServerLayout"
Identifier "Default Layout"
screen "Default Screen"
Inputdevice "Generic Keyboard"
Inputdevice "Configured Mouse"

# Uncomment if you have a wacom tablet
# InputDevice "stylus" "SendCoreEvents"
# InputDevice "cursor" "SendCoreEvents"
# InputDevice "eraser" "SendCoreEvents"
EndSection

Note that the Inputdevice must be called the same in both places

[glpnet1]

My xorg is as follows.
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildmeister@builder3) Thu Oct 4 10:34:46 PDT 2007

# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder3) Thu Oct 4 10:33:51 PDT 2007
# xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg

Section "ServerLayout"

# Uncomment if you have a wacom tablet
# InputDevice "stylus" "SendCoreEvents"
# InputDevice "cursor" "SendCoreEvents"
# InputDevice "eraser" "SendCoreEvents"
Identifier "Default Layout"
Screen 0 "Screen0" 1024 0
Screen 1 "Screen1" LeftOf "Screen0"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
EndSection

Section "Files"
EndSection

Section "Module"
Load "glx"
EndSection

Section "ServerFlags"
Option "Xinerama" "0"
EndSection

Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection

Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection

Section "InputDevice"
Identifier "stylus"
Driver "wacom"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection

Section "InputDevice"
Identifier "eraser"
Driver "wacom"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection

Section "InputDevice"
Identifier "cursor"
Driver "wacom"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection

Section "Monitor"
Identifier "Generic Monitor"
Option "DPMS"
EndSection

Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Proview"
HorizSync 30.0 - 80.0
VertRefresh 60.0 - 75.0
EndSection

Section "Monitor"
Identifier "Monitor1"
VendorName "Unknown"
ModelName "COMPAQ 7550"
HorizSync 30.0 - 86.0
VertRefresh 50.0 - 140.0
EndSection

Section "Device"
Identifier "nVidia Corporation G71 [GeForce 7300 GS]"
Driver "nvidia"
EndSection

Section "Device"
Identifier "Videocard0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 7300 GS"
BusID "PCI:1:0:0"
Screen 0
EndSection

Section "Device"
Identifier "Videocard1"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 7300 GS"
BusID "PCI:1:0:0"
Screen 1
EndSection

Section "Screen"
Identifier "Default Screen"
Device "nVidia Corporation G71 [GeForce 7300 GS]"
Monitor "Generic Monitor"
DefaultDepth 24
Option "AddARGBGLXVisuals" "True"
SubSection "Display"
Depth 24
Modes "1440x1440" "1440x900" "1280x1024" "1024x768" "832x624" "800x600" "720x400" "640x480"
EndSubSection
EndSection

Section "Screen"
Identifier "Screen0"
Device "Videocard0"
Monitor "Monitor0"
DefaultDepth 24
Option "TwinView" "0"
Option "metamodes" "CRT-0: 1440x900 +0+0; CRT-0: 1024x768 +0+0; CRT-0: 832x624 +0+0; CRT-0: 800x600 +0+0; CRT-0: 640x480 +0+0"
EndSection

Section "Screen"
Identifier "Screen1"
Device "Videocard1"
Monitor "Monitor1"
DefaultDepth 24
Option "TwinView" "0"
Option "metamodes" "CRT-1: 1024x768_75 +0+0"
EndSection

Section "Extensions"
Option "Composite" "Enable"
EndSection