[SOLVED] USB 3.0 Ports Inactive

Questions about hardware,drivers and peripherals
Forum rules
Before you post please read how to get help

[SOLVED] USB 3.0 Ports Inactive

Postby N1X3L on Sat Sep 08, 2012 9:01 pm

Hi all,

I'm enjoying the latest Mint (System: Kernel 3.2.0-30-generic x86_64 (64 bit) Distro Linux Mint 13 Maya – Cinnamon), but there have been a couple problems I'm slowly working through. One problem I can't seem to make anymore headway on, is that my USB 3.0 ports are non–functional. I know my kernel should support USB 3.0. Any advice would be greatly appreciated. Thank you!

I'm CLI shy, but I managed to generate these...

lsusb
Code: Select all
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 002: ID 2109:0810 
Bus 006 Device 002: ID 2109:0810 
Bus 001 Device 004: ID 2109:3431 
Bus 001 Device 005: ID 2109:3431 
Bus 002 Device 003: ID 058f:6364 Alcor Micro Corp. Hi-Speed 7-in-1 Flash Card Reader/Writer [Sabrent]
Bus 001 Device 006: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
Bus 001 Device 007: ID 099a:7010 Zippy Technology Corp.
Bus 001 Device 008: ID 0461:4d38 Primax Electronics, Ltd


lspci -v
Code: Select all
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, fast devsel, latency 0
   Capabilities: <access denied>

00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
   I/O behind bridge: 0000e000-0000efff
   Memory behind bridge: f6000000-f80fffff
   Prefetchable memory behind bridge: 00000000d0000000-00000000dbffffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:01.1 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
   I/O behind bridge: 0000d000-0000dfff
   Memory behind bridge: f2000000-f40fffff
   Prefetchable memory behind bridge: 00000000c0000000-00000000cbffffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, fast devsel, latency 0, IRQ 73
   Memory at f0425000 (64-bit, non-prefetchable) [size=16]
   Capabilities: <access denied>
   Kernel driver in use: mei
   Kernel modules: mei

00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 05)
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, fast devsel, latency 0, IRQ 71
   Memory at f0400000 (32-bit, non-prefetchable) [size=128K]
   Memory at f0424000 (32-bit, non-prefetchable) [size=4K]
   I/O ports at f040 [size=32]
   Capabilities: <access denied>
   Kernel driver in use: e1000e
   Kernel modules: e1000e

00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, medium devsel, latency 0, IRQ 23
   Memory at f0423000 (32-bit, non-prefetchable) [size=1K]
   Capabilities: <access denied>
   Kernel driver in use: ehci_hcd

00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=03, subordinate=08, sec-latency=0
   Memory behind bridge: ec000000-f03fffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
   Memory behind bridge: f8600000-f86fffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
   Memory behind bridge: f8500000-f85fffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
   I/O behind bridge: 0000c000-0000cfff
   Memory behind bridge: f8400000-f84fffff
   Prefetchable memory behind bridge: 00000000cc000000-00000000cc0fffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
   I/O behind bridge: 0000b000-0000bfff
   Memory behind bridge: f8300000-f83fffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:1c.6 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 (rev b5) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0
   I/O behind bridge: 0000a000-0000afff
   Memory behind bridge: f8200000-f82fffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, medium devsel, latency 0, IRQ 23
   Memory at f0422000 (32-bit, non-prefetchable) [size=1K]
   Capabilities: <access denied>
   Kernel driver in use: ehci_hcd

00:1f.0 ISA bridge: Intel Corporation P67 Express Chipset Family LPC Controller (rev 05)
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, medium devsel, latency 0
   Capabilities: <access denied>
   Kernel modules: iTCO_wdt

00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 53
   I/O ports at f090 [size=8]
   I/O ports at f080 [size=4]
   I/O ports at f070 [size=8]
   I/O ports at f060 [size=4]
   I/O ports at f020 [size=32]
   Memory at f0421000 (32-bit, non-prefetchable) [size=2K]
   Capabilities: <access denied>
   Kernel driver in use: ahci

00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: medium devsel, IRQ 5
   Memory at f0420000 (64-bit, non-prefetchable) [size=256]
   I/O ports at 1180 [size=32]
   Kernel modules: i2c-i801

01:00.0 VGA compatible controller: NVIDIA Corporation GF110 [GeForce GTX 560 Ti] (rev a1) (prog-if 00 [VGA controller])
   Subsystem: Device 196e:0898
   Flags: bus master, fast devsel, latency 0, IRQ 16
   Memory at f6000000 (32-bit, non-prefetchable) [size=32M]
   Memory at d0000000 (64-bit, prefetchable) [size=128M]
   Memory at d8000000 (64-bit, prefetchable) [size=64M]
   I/O ports at e000 [size=128]
   [virtual] Expansion ROM at f8000000 [disabled] [size=512K]
   Capabilities: <access denied>
   Kernel driver in use: nvidia
   Kernel modules: nvidia_current, nouveau, nvidiafb
 
01:00.1 Audio device: NVIDIA Corporation GF110 High Definition Audio Controller (rev a1)
   Subsystem: Device 196e:0898
   Flags: bus master, fast devsel, latency 0, IRQ 17
   Memory at f8080000 (32-bit, non-prefetchable) [size=16K]
   Capabilities: <access denied>
   Kernel driver in use: snd_hda_intel
   Kernel modules: snd-hda-intel

02:00.0 VGA compatible controller: NVIDIA Corporation GF110 [GeForce GTX 560 Ti] (rev a1) (prog-if 00 [VGA controller])
   Subsystem: Device 196e:0898
   Flags: bus master, fast devsel, latency 0, IRQ 17
   Memory at f2000000 (32-bit, non-prefetchable) [size=32M]
   Memory at c0000000 (64-bit, prefetchable) [size=128M]
   Memory at c8000000 (64-bit, prefetchable) [size=64M]
   I/O ports at d000 [size=128]
   [virtual] Expansion ROM at f4000000 [disabled] [size=512K]
   Capabilities: <access denied>
   Kernel driver in use: nvidia
   Kernel modules: nvidia_current, nouveau, nvidiafb

02:00.1 Audio device: NVIDIA Corporation GF110 High Definition Audio Controller (rev a1)
   Subsystem: Device 196e:0898
   Flags: bus master, fast devsel, latency 0, IRQ 18
   Memory at f4080000 (32-bit, non-prefetchable) [size=16K]
   Capabilities: <access denied>
   Kernel driver in use: snd_hda_intel
   Kernel modules: snd-hda-intel

03:00.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Memory at f0300000 (32-bit, non-prefetchable) [size=128K]
   Bus: primary=03, secondary=04, subordinate=08, sec-latency=0
   Memory behind bridge: ec000000-f02fffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

04:00.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=04, secondary=05, subordinate=05, sec-latency=0
   Memory behind bridge: ec000000-f02fffff
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

04:05.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=04, secondary=06, subordinate=06, sec-latency=0
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

04:07.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=04, secondary=07, subordinate=07, sec-latency=0
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

04:09.0 PCI bridge: PLX Technology, Inc. PEX 8608 8-lane, 8-Port PCI Express Gen 2 (5.0 GT/s) Switch (rev ba) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0
   Bus: primary=04, secondary=08, subordinate=08, sec-latency=0
   Capabilities: <access denied>
   Kernel driver in use: pcieport
   Kernel modules: shpchp

05:00.0 Audio device: Creative Labs X-Fi Titanium series [EMU20k2] (rev 04)
   Subsystem: Creative Labs Device 0043
   Flags: bus master, fast devsel, latency 0, IRQ 16
   Memory at f0200000 (64-bit, non-prefetchable) [size=64K]
   Memory at f0000000 (64-bit, non-prefetchable) [size=2M]
   Memory at ec000000 (64-bit, non-prefetchable) [size=64M]
   Capabilities: <access denied>
   Kernel driver in use: snd_ctxfi
   Kernel modules: snd-ctxfi

09:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI])
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, fast devsel, latency 0, IRQ 17
   Memory at f8600000 (64-bit, non-prefetchable) [size=8K]
   Capabilities: <access denied>
   Kernel driver in use: xhci_hcd

0a:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI])
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, fast devsel, latency 0, IRQ 18
   Memory at f8500000 (64-bit, non-prefetchable) [size=8K]
   Capabilities: <access denied>
   Kernel driver in use: xhci_hcd

0b:00.0 SATA controller: JMicron Technology Corp. JMB362 SATA Controller (rev 10) (prog-if 01 [AHCI 1.0])
   Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
   Flags: bus master, fast devsel, latency 0, IRQ 19
   I/O ports at c040 [size=8]
   I/O ports at c030 [size=4]
   I/O ports at c020 [size=8]
   I/O ports at c010 [size=4]
   I/O ports at c000 [size=16]
   Memory at f8410000 (32-bit, non-prefetchable) [size=512]
   [virtual] Expansion ROM at cc000000 [disabled] [size=64K]
   Capabilities: <access denied>
   Kernel driver in use: ahci

0c:00.0 SATA controller: Marvell Technology Group Ltd. Device 9182 (rev 11) (prog-if 01 [AHCI 1.0])
   Subsystem: ASUSTeK Computer Inc. Device 8493
   Flags: bus master, fast devsel, latency 0, IRQ 54
   I/O ports at b040 [size=8]
   I/O ports at b030 [size=4]
   I/O ports at b020 [size=8]
   I/O ports at b010 [size=4]
   I/O ports at b000 [size=16]
   Memory at f8310000 (32-bit, non-prefetchable) [size=512]
   Expansion ROM at f8300000 [disabled] [size=64K]
   Capabilities: <access denied>
   Kernel driver in use: ahci

0d:00.0 Ethernet controller: Intel Corporation 82583V Gigabit Network Connection
   Subsystem: ASUSTeK Computer Inc. Device 8457
   Flags: bus master, fast devsel, latency 0, IRQ 72
   Memory at f8200000 (32-bit, non-prefetchable) [size=128K]
   I/O ports at a000 [size=32]
   Memory at f8220000 (32-bit, non-prefetchable) [size=16K]
   Capabilities: <access denied>
   Kernel driver in use: e1000e
   Kernel modules: e1000e
Last edited by N1X3L on Mon Sep 10, 2012 11:52 am, edited 1 time in total.
N1X3L
Level 1
Level 1
 
Posts: 22
Joined: Fri Nov 04, 2011 3:23 am
Location: Canindeyú, Paraguay

Linux Mint is funded by ads and donations.
 

Re: USB 3.0 Ports Inactive

Postby remoulder on Sun Sep 09, 2012 2:44 pm

N1X3L wrote:09:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI])
Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at f8600000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd


From your output there doesn't appear to be a problem, the ports are recognized and have a driver. If devices don't work, are they usb 3 compatible?
[Edit] your original post and add [SOLVED] once your question is resolved.

“The people are my God” stressing the factor determining man’s destiny lies within man not in anything outside man, and thereby defining man as the dominator and remoulder of the world.
User avatar
remoulder
Level 17
Level 17
 
Posts: 7667
Joined: Fri May 09, 2008 1:14 pm

Re: USB 3.0 Ports Inactive

Postby N1X3L on Sun Sep 09, 2012 4:37 pm

That's odd. :? I am absolutely certain the devices are USB 3.0 compatible, and they function on this same computer when I'm booted into Windows 7 as such. Can you think of something else that could be going on? Also, thank you for the help you've already given, and anymore you are able to provide — know that it's appreciated. :)
Image
N1X3L
Level 1
Level 1
 
Posts: 22
Joined: Fri Nov 04, 2011 3:23 am
Location: Canindeyú, Paraguay

Re: USB 3.0 Ports Inactive

Postby remoulder on Sun Sep 09, 2012 5:42 pm

If you plug in a device then immediately enter dmesg | tail in a terminal, is there mention of a detected device, errors? Try this with different ports/devices.
[Edit] your original post and add [SOLVED] once your question is resolved.

“The people are my God” stressing the factor determining man’s destiny lies within man not in anything outside man, and thereby defining man as the dominator and remoulder of the world.
User avatar
remoulder
Level 17
Level 17
 
Posts: 7667
Joined: Fri May 09, 2008 1:14 pm

Re: USB 3.0 Ports Inactive

Postby N1X3L on Mon Sep 10, 2012 2:42 am

Thank you for recommending that I "try this with different ports/devices"; it forced me to overcome my natural lazy tendency of just plugging peripherals in the front. So it turns out USB 3.0 works — but only in back? :? Why would that be?

After boot, no storage devices tried yet
dmesg | tail
Code: Select all
[ 2608.039922] [UFW BLOCK] IN=eth0 OUT= MAC=33:33:00:00:00:fb:58:b0:35:f3:4d:77:86:dd SRC=fe80:0000:0000:0000:5ab0:35ff:fef3:4d77 DST=ff02:0000:0000:0000:0000:0000:0000:00fb LEN=241 TC=0 HOPLIMIT=255 FLOWLBL=0 FRAG:1232 ID:ac27eb16 PROTO=UDP
[ 2611.135906] [UFW BLOCK] IN=eth0 OUT= MAC=33:33:00:00:00:fb:58:b0:35:f3:4d:77:86:dd SRC=fe80:0000:0000:0000:5ab0:35ff:fef3:4d77 DST=ff02:0000:0000:0000:0000:0000:0000:00fb LEN=241 TC=0 HOPLIMIT=255 FLOWLBL=0 FRAG:1232 ID:8a43aadc PROTO=UDP
[ 2615.760354] [UFW BLOCK] IN=eth0 OUT= MAC=33:33:00:00:00:fb:58:b0:35:f3:4d:77:86:dd SRC=fe80:0000:0000:0000:5ab0:35ff:fef3:4d77 DST=ff02:0000:0000:0000:0000:0000:0000:00fb LEN=118 TC=0 HOPLIMIT=255 FLOWLBL=0 FRAG:1232 ID:8dd87252 PROTO=UDP
[ 2618.873015] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:08:86:3b:2a:3b:22:08:00 SRC=192.168.2.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=51932 PROTO=2
[ 2618.935481] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:15:e3:3b:08:00 SRC=10.100.102.103 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=52631 PROTO=2
[ 2642.794862] [UFW BLOCK] IN=eth0 OUT= MAC=33:33:00:00:00:fb:58:b0:35:f3:4d:77:86:dd SRC=fe80:0000:0000:0000:5ab0:35ff:fef3:4d77 DST=ff02:0000:0000:0000:0000:0000:0000:00fb LEN=129 TC=0 HOPLIMIT=255 FLOWLBL=0 FRAG:1232 ID:83ab9ab2 PROTO=UDP
[ 2656.207386] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:20:aa:4b:c2:b8:c9:08:00 SRC=10.100.100.30 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=0 DF PROTO=2
[ 2660.747632] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:ef:d2:eb:08:00 SRC=10.100.100.111 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=38314 PROTO=2
[ 2678.868079] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:08:86:3b:2a:3b:22:08:00 SRC=192.168.2.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=51999 PROTO=2
[ 2721.277198] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:ef:d2:eb:08:00 SRC=10.100.100.111 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=58313 PROTO=2


USB 2.0 Flashdrive in front USB 3.0 port: Inactive
dmesg | tail
Code: Select all
[ 2656.207386] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:20:aa:4b:c2:b8:c9:08:00 SRC=10.100.100.30 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=0 DF PROTO=2
[ 2660.747632] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:ef:d2:eb:08:00 SRC=10.100.100.111 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=38314 PROTO=2
[ 2678.868079] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:08:86:3b:2a:3b:22:08:00 SRC=192.168.2.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=51999 PROTO=2
[ 2721.277198] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:ef:d2:eb:08:00 SRC=10.100.100.111 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=58313 PROTO=2
[ 2723.899965] [UFW BLOCK] IN=eth0 OUT= MAC=33:33:00:00:00:fb:58:b0:35:f3:4d:77:86:dd SRC=fe80:0000:0000:0000:5ab0:35ff:fef3:4d77 DST=ff02:0000:0000:0000:0000:0000:0000:00fb LEN=112 TC=0 HOPLIMIT=255 FLOWLBL=0 FRAG:1232 ID:de54c1d2 PROTO=UDP
[ 2730.921329] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:15:e3:3b:08:00 SRC=10.100.102.103 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=59704 PROTO=2
[ 2739.826562] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:20:aa:4b:b0:f7:b9:08:00 SRC=10.100.102.113 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=0 DF PROTO=2
[ 2782.121984] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:20:aa:4b:c2:b8:c9:08:00 SRC=10.100.100.30 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=0 DF PROTO=2
[ 2783.138369] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:4c:b1:99:16:e9:a2:08:00 SRC=10.100.100.200 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=54543 PROTO=2
[ 2799.790018] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:20:aa:4b:a1:bf:eb:08:00 SRC=10.100.104.141 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=0 DF PROTO=2


USB 2.0 Flashdrive in rear USB 3.0 port: Active
dmesg | tail
Code: Select all
[ 2918.702572] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:08:86:3b:2a:3b:22:08:00 SRC=192.168.2.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=52275 PROTO=2
[ 2959.854548] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:ef:d2:eb:08:00 SRC=10.100.100.111 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=1085 PROTO=2
[ 2967.212746] [UFW BLOCK] IN=eth0 OUT= MAC=33:33:00:00:00:fb:58:b0:35:f3:4d:77:86:dd SRC=fe80:0000:0000:0000:5ab0:35ff:fef3:4d77 DST=ff02:0000:0000:0000:0000:0000:0000:00fb LEN=115 TC=0 HOPLIMIT=255 FLOWLBL=0 FRAG:1232 ID:30353792 PROTO=UDP
[ 2970.272968] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:15:e3:3b:08:00 SRC=10.100.102.103 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=3425 PROTO=2
[ 2978.686661] usb 1-1.3.4: new high-speed USB device number 9 using ehci_hcd
[ 2978.712265] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:08:86:3b:2a:3b:22:08:00 SRC=192.168.2.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=52352 PROTO=2
[ 2978.779746] scsi11 : usb-storage 1-1.3.4:1.0
[ 2979.778707] scsi 11:0:0:0: Direct-Access     PNY      USB 2.0 FD       8.02 PQ: 0 ANSI: 0 CCS
[ 2979.779398] sd 11:0:0:0: Attached scsi generic sg7 type 0
[ 2979.781259] sd 11:0:0:0: [sdg] Attached SCSI removable disk


USB 3.0 Hard drive in rear USB 3.0 port: Active
dmesg | tail
Code: Select all
[ 3079.251431] sd 12:0:0:0: Attached scsi generic sg7 type 0
[ 3079.251613] sd 12:0:0:0: [sdg] 732558336 4096-byte logical blocks: (3.00 TB/2.72 TiB)
[ 3079.251720] scsi 12:0:0:1: Attached scsi generic sg8 type 13
[ 3079.252233] sd 12:0:0:0: [sdg] Write Protect is off
[ 3079.252240] sd 12:0:0:0: [sdg] Mode Sense: 47 00 10 08
[ 3079.253394] sd 12:0:0:0: [sdg] No Caching mode page present
[ 3079.253401] sd 12:0:0:0: [sdg] Assuming drive cache: write through
[ 3079.254025] sd 12:0:0:0: [sdg] 732558336 4096-byte logical blocks: (3.00 TB/2.72 TiB)
[ 3079.255351] sd 12:0:0:0: [sdg] No Caching mode page present
[ 3079.255356] sd 12:0:0:0: [sdg] Assuming drive cache: write through


USB 3.0 Hard drive in front USB 3.0 port: Inactive
dmesg | tail
Code: Select all
[ 3338.472727] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:08:86:3b:2a:3b:22:08:00 SRC=192.168.2.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=52759 PROTO=2
[ 3339.095422] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:00:13:d3:11:9d:bf:08:00 SRC=10.100.102.54 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2
[ 3381.548977] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:ef:d2:eb:08:00 SRC=10.100.100.111 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=31132 PROTO=2
[ 3381.735110] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:20:aa:4b:c2:b8:c9:08:00 SRC=10.100.100.30 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=0 DF PROTO=2
[ 3398.627221] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:0c:77:1a:91:60:45:08:00 SRC=10.100.104.117 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=30972 PROTO=2
[ 3438.990096] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:ef:d2:eb:08:00 SRC=10.100.100.111 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=760 PROTO=2
[ 3452.522607] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:15:e3:3b:08:00 SRC=10.100.102.103 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=27002 PROTO=2
[ 3458.365254] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:08:86:3b:2a:3b:22:08:00 SRC=192.168.2.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=52916 PROTO=2
[ 3503.121879] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:fb:08:86:3b:15:e3:3b:08:00 SRC=10.100.102.103 DST=224.0.0.251 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=28484 PROTO=2
[ 3507.659920] [UFW BLOCK] IN=eth0 OUT= MAC=01:00:5e:00:00:01:20:aa:4b:c2:b8:c9:08:00 SRC=10.100.100.30 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=0 DF PROTO=2
Image
N1X3L
Level 1
Level 1
 
Posts: 22
Joined: Fri Nov 04, 2011 3:23 am
Location: Canindeyú, Paraguay

Re: USB 3.0 Ports Inactive

Postby remoulder on Mon Sep 10, 2012 8:44 am

N1X3L wrote:Why would that be

Probably not connected to the front ports? Glad it works after all.
[Edit] your original post and add [SOLVED] once your question is resolved.

“The people are my God” stressing the factor determining man’s destiny lies within man not in anything outside man, and thereby defining man as the dominator and remoulder of the world.
User avatar
remoulder
Level 17
Level 17
 
Posts: 7667
Joined: Fri May 09, 2008 1:14 pm

Re: USB 3.0 Ports Inactive

Postby N1X3L on Mon Sep 10, 2012 11:51 am

I would think the same thing, except all those front "inactive" ports function normally in Windows — so I know they are plugged in. :|

You've already been a tremendous help, and I appreciate that. You've also given me enough sure-footing to keep exploring this myself. I'll relabel this post as solved, but will continue posting here if I discover what is going on with the inactivity of those front ports. Thanks again! :D
Image
N1X3L
Level 1
Level 1
 
Posts: 22
Joined: Fri Nov 04, 2011 3:23 am
Location: Canindeyú, Paraguay

Re: [SOLVED] USB 3.0 Ports Inactive

Postby baj on Mon Feb 11, 2013 1:42 am

I just loaded Mint yesterday and I have the same issue. I have an HP 8740w laptop though and it only has two USB 3.0 ports right next to each other. Neither works

# dmesg | tail
[ 8845.271839] generic-usb 0003:093A:2510.0009: input,hidraw2: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:1d.0-1.1/input0
[ 8849.473776] usb 2-1.1: USB disconnect, device number 11
[ 8849.776169] usb 2-1.1: new low-speed USB device number 12 using ehci_hcd
[ 8849.875585] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input24
[ 8849.875915] generic-usb 0003:093A:2510.000A: input,hidraw2: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:1d.0-1.1/input0
[ 8855.266439] usb 3-2: new high-speed USB device number 7 using xhci_hcd
[ 8855.518644] usb 3-2: Device not responding to set address.
[ 8855.721874] usb 3-2: Device not responding to set address.
[ 8855.925309] usb 3-2: device not accepting address 7, error -71
[ 8855.981185] hub 3-0:1.0: unable to enumerate USB device on port 2

Any ideas?

Thanks,
-Brad
baj
Level 1
Level 1
 
Posts: 30
Joined: Mon Feb 11, 2013 1:36 am

Linux Mint is funded by ads and donations.
 

Return to Hardware Support

Who is online

Users browsing this forum: No registered users and 13 guests