lspcmcia

Questions about hardware,drivers and peripherals
Forum rules
Before you post please read this

lspcmcia

Postby zippytex on Wed Feb 13, 2013 12:04 pm

I have a Toshiba Tecra M9 and I am trying to use an pcmcia adapter for SD cards.
I cannot get the laptop to recognize the pcmcia adapter card. I am using Linux Mint 13.

I ran lspcmcia and here's what showed up:
socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:06:06.0)

Can anyone tell me what this means?

This card inserted into a Dell c400 with puppy is recognized.
Why would it work in one linux system and in another?

Is there a list of pcmcia cards that have been found to work in Linux Mint?
OR, is the pcmcia slot being recognized in the Tecra M9?

Thank you for your help.
Mary
zippytex
Level 1
Level 1
 
Posts: 43
Joined: Mon Jul 11, 2011 3:22 pm

Linux Mint is funded by ads and donations.
 

Re: lspcmcia

Postby zippytex on Wed Feb 13, 2013 1:13 pm

I booted up with Puppy Slacko and used it live.

When I ran lspcmcia, I received the following:
Socket 0 Bridge: [yenta cardbus] (bus ID: 0000:06.0)
Socket 0 Device 0: [--no driver--] (bus ID: 0000:06.0)

I checked the BIOS and did not find anything I could change relating to PCMCIA(PCIC) and cardbus operations. (Toshiba Tecra M9)

So, here is a request. Where can I find a pcmcia SD card adapter that Linux Mint 13 will recognize?
Is there an approved list somewhere? I will buy whatever works.

Thanks.
zippytex
Level 1
Level 1
 
Posts: 43
Joined: Mon Jul 11, 2011 3:22 pm

Re: lspcmcia

Postby AlbertP on Wed Feb 13, 2013 1:35 pm

Socket 0 Bridge is the slot in your computer, the actual card is Socket 0 Device 0, with no driver loaded. Could you run "pccardctl ident" to identify the card? lspcmcia only shows the driver, if any, not the card's model.

Also, which kernel version does that Puppy live system use?

Edit. Could you post the output of lspci too?
Registered Linux User #528502
Image
Feel free to correct me if I'm trying to write in Spanish, French or German.
AlbertP
Level 16
Level 16
 
Posts: 6504
Joined: Sun Jan 30, 2011 12:38 pm
Location: The Netherlands

Re: lspcmcia

Postby zippytex on Wed Feb 13, 2013 2:51 pm

The live cd is for Slacko 5.4-firefox-4g.iso

Thanks for your help

I ran this with the pc card inserted into the Dell c400, running precise puppy and I could access the pcmcia card

# lspcmcia
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:02:01.0)
Socket 0 Device 0: [pata_pcmcia] (bus ID: 0.0)

# pccardctl ident
Socket 0:
product info: “
“, “
“, “
“, “ “
manfid: 0x0105, 0x0201
function: 4 (fixed disk)


I ran this with the pc card inserted into the Tecra M9, booted with Puppy

pccardctl ident
Socket 0:
no product info available
manfid: 0x0105, 0x0201
zippytex
Level 1
Level 1
 
Posts: 43
Joined: Mon Jul 11, 2011 3:22 pm

Re: lspcmcia

Postby AlbertP on Wed Feb 13, 2013 3:21 pm

Ok, so it seems to be a problem with the Toshiba laptop? Could you run lspci on that laptop with the card inserted and post the output?
Registered Linux User #528502
Image
Feel free to correct me if I'm trying to write in Spanish, French or German.
AlbertP
Level 16
Level 16
 
Posts: 6504
Joined: Sun Jan 30, 2011 12:38 pm
Location: The Netherlands

Re: lspcmcia

Postby zippytex on Fri Feb 15, 2013 12:07 pm

With the pc card inserted into the Toshiba Tecra M9, below is the terminal output.

Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:06:06.0)

Thanks for your help.
Mary
zippytex
Level 1
Level 1
 
Posts: 43
Joined: Mon Jul 11, 2011 3:22 pm

Re: lspcmcia

Postby AlbertP on Fri Feb 15, 2013 12:17 pm

That's lspcmcia. But could you run lspci on the Toshiba laptop?
Registered Linux User #528502
Image
Feel free to correct me if I'm trying to write in Spanish, French or German.
AlbertP
Level 16
Level 16
 
Posts: 6504
Joined: Sun Jan 30, 2011 12:38 pm
Location: The Netherlands

Re: lspcmcia

Postby zippytex on Sat Feb 16, 2013 10:55 am

Sorry, lspci is below.

zippytex@zippytex-TECRA-M9 ~ $ sudo
usage: sudo [-D level] -h | -K | -k | -V
usage: sudo -v [-AknS] [-D level] [-g groupname|#gid] [-p prompt] [-u user
name|#uid]
usage: sudo -l[l] [-AknS] [-D level] [-g groupname|#gid] [-p prompt] [-U user
name] [-u user name|#uid] [-g groupname|#gid] [command]
usage: sudo [-AbEHknPS] [-C fd] [-D level] [-g groupname|#gid] [-p prompt] [-u
user name|#uid] [-g groupname|#gid] [VAR=value] [-i|-s] [<command>]
usage: sudo -e [-AknS] [-C fd] [-D level] [-g groupname|#gid] [-p prompt] [-u
user name|#uid] file ...
zippytex@zippytex-TECRA-M9 ~ $ lspci
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile PM965/GM965/GL960 PCI Express Root Port (rev 03)
00:03.0 Communication controller: Intel Corporation Mobile PM965/GM965 MEI Controller (rev 03)
00:19.0 Ethernet controller: Intel Corporation 82566MM Gigabit Network Connection (rev 03)
00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)
00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03)
00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 03)
00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)
00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)
00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)
00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M-E) LPC Interface Controller (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03)
00:1f.2 SATA controller: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 03)
01:00.0 VGA compatible controller: NVIDIA Corporation G86M [Quadro NVS 130M] (rev a1)
02:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
06:0b.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
06:0b.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller
06:0b.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller
zippytex@zippytex-TECRA-M9 ~ $


Thanks.
zippytex
Level 1
Level 1
 
Posts: 43
Joined: Mon Jul 11, 2011 3:22 pm

Re: lspcmcia

Postby AlbertP on Sat Feb 16, 2013 1:11 pm

It's just a Texas Instruments CardBus bridge.
Code: Select all
06:0b.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller

That's nothing special. It should work. Actually, I have a HP laptop with the same CardBus bridge here. I have tried a 32-bit PCMCIA card in it some time ago (a 3Com OfficeConnect ethernet+modem card), and that card is detected without any problem. Your card appears to be a 16-bit PCMCIA device, however, and those are quite different. 16-bit PCMCIA cards are rare nowadays, but still I'd expect it to work. Could you boot the computer without the card in the slot, and run:
Code: Select all
sudo dmesg -C
(which produces no output)

Then please insert the card, wait a moment, and run:
Code: Select all
dmesg

Please post the output of that.
Registered Linux User #528502
Image
Feel free to correct me if I'm trying to write in Spanish, French or German.
AlbertP
Level 16
Level 16
 
Posts: 6504
Joined: Sun Jan 30, 2011 12:38 pm
Location: The Netherlands

Re: lspcmcia

Postby zippytex on Sun Feb 17, 2013 11:05 am

I took out the card and restarted the laptop.

I entered sudo dmesg -c and got 8 pages of text, do you want that?

Then I entered d-mesg and the following appeared:

zippytex@zippytex-TECRA-M9 ~ $ dmesg
[ 101.648202] pcmcia_socket pcmcia_socket0: pccard: PCMCIA card inserted into slot 0
[ 101.648217] pcmcia_socket pcmcia_socket0: cs: memory probe 0xc4600000-0xc9ffffff: excluding 0xc4ba0000-0xc56dffff 0xc5c80000-0xc621ffff 0xc6d60000-0xc72fffff 0xc7e40000-0xc83dffff 0xc8f20000-0xc94bffff
zippytex@zippytex-TECRA-M9 ~ $

Again, I thank you for all your help.
Mary
zippytex
Level 1
Level 1
 
Posts: 43
Joined: Mon Jul 11, 2011 3:22 pm

Re: lspcmcia

Postby AlbertP on Sun Feb 17, 2013 11:10 am

sudo dmesg -C clears the log of the boot messages, so that we'll only have the messages that appear after the insertion of a card.
If you write a lowercase c then it indeed prints the whole log of your system's boot before clearing it, with an uppercase -C it clears the log without outputting the old contents first. But that does not really matter.

It doesn't appear to do anything after the insertion of the card. Does the PC Card slot of the laptop work in Windows? If not, I think it's a hardware failure or something like that.
Registered Linux User #528502
Image
Feel free to correct me if I'm trying to write in Spanish, French or German.
AlbertP
Level 16
Level 16
 
Posts: 6504
Joined: Sun Jan 30, 2011 12:38 pm
Location: The Netherlands

Re: lspcmcia

Postby zippytex on Sun Feb 17, 2013 11:44 am

Thanks. I have learned much while talking to you. I am writing it down in my little linux book.

I bought the unit used last year and it is possible it was broken when I received it.

I think I will just forget it is there, because it is not worth messing with Windows again.

I mainly use my computer for family history research and the web. With gramps and Linux Mint my needs are met.

Thanks again, it must be nice to have such knowledge as you do.

Mary :D
zippytex
Level 1
Level 1
 
Posts: 43
Joined: Mon Jul 11, 2011 3:22 pm

support for pcmcia Tecra M9

Postby zippytex on Wed Jun 05, 2013 3:19 pm

Following your instructions here is what I have as of today 6/5/13

zippytex@zippytex-TECRA-M9 ~ $ sudo
usage: sudo [-D level] -h | -K | -k | -V
usage: sudo -v [-AknS] [-D level] [-g groupname|#gid] [-p prompt] [-u user
name|#uid]
usage: sudo -l[l] [-AknS] [-D level] [-g groupname|#gid] [-p prompt] [-U user
name] [-u user name|#uid] [-g groupname|#gid] [command]
usage: sudo [-AbEHknPS] [-C fd] [-D level] [-g groupname|#gid] [-p prompt] [-u
user name|#uid] [-g groupname|#gid] [VAR=value] [-i|-s] [<command>]
usage: sudo -e [-AknS] [-C fd] [-D level] [-g groupname|#gid] [-p prompt] [-u
user name|#uid] file ...
zippytex@zippytex-TECRA-M9 ~ $ sudo dmesg -C
[sudo] password for zippytex:
zippytex@zippytex-TECRA-M9 ~ $ dmesg
[ 118.052195] pcmcia_socket pcmcia_socket0: pccard: PCMCIA card inserted into slot 0
[ 118.052210] pcmcia_socket pcmcia_socket0: cs: memory probe 0xc4600000-0xc9ffffff: excluding 0xc4ba0000-0xc513ffff 0xc5c80000-0xc621ffff 0xc6d60000-0xc72fffff 0xc7e40000-0xc83dffff 0xc8f20000-0xc94bffff
zippytex@zippytex-TECRA-M9 ~ $


Looks like a foreign lanuage where you can only understand a work here and there. Maybe it is because it is a 16bit card and not a 32 bit?
Thanks, Mary
zippytex
Level 1
Level 1
 
Posts: 43
Joined: Mon Jul 11, 2011 3:22 pm

Re: lspcmcia

Postby AlbertP on Wed Jun 05, 2013 4:01 pm

That's indeed the case, but a card is recognized so your computer is certainly capable of using 16-bit PCMCIA cards.

If you wait a while and run dmesg again, does anything new appear?

Maybe you can do this to load the pata_pcmcia driver that Puppy used:
Code: Select all
sudo modprobe pata_pcmcia
Registered Linux User #528502
Image
Feel free to correct me if I'm trying to write in Spanish, French or German.
AlbertP
Level 16
Level 16
 
Posts: 6504
Joined: Sun Jan 30, 2011 12:38 pm
Location: The Netherlands

Re: lspcmcia

Postby zippytex on Wed Jun 05, 2013 4:55 pm

Below is the answer, I hope.

zippytex@zippytex-TECRA-M9 ~ $ CODE: SELECT ALL
CODE:: command not found
zippytex@zippytex-TECRA-M9 ~ $ sudo modprobe pata_pcmcia
[sudo] password for zippytex:
zippytex@zippytex-TECRA-M9 ~ $
zippytex@zippytex-TECRA-M9 ~ $ dmesg
[ 118.052195] pcmcia_socket pcmcia_socket0: pccard: PCMCIA card inserted into slot 0
[ 118.052210] pcmcia_socket pcmcia_socket0: cs: memory probe 0xc4600000-0xc9ffffff: excluding 0xc4ba0000-0xc513ffff 0xc5c80000-0xc621ffff 0xc6d60000-0xc72fffff 0xc7e40000-0xc83dffff 0xc8f20000-0xc94bffff
[ 1572.134887] PM: Syncing filesystems ... done.
[ 1572.139976] PM: Preparing system for mem sleep
[ 1572.405903] mmc0: card 1234 removed
[ 1572.411624] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 1572.428123] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 1572.448115] PM: Entering mem sleep
[ 1572.448130] Suspending console(s) (use no_console_suspend to debug)
[ 1572.449145] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 1572.449223] sd 0:0:0:0: [sda] Stopping disk
[ 1572.520573] serial 00:0c: disabled
[ 1572.604852] [drm] nouveau 0000:01:00.0: Disabling fbcon acceleration...
[ 1572.604855] [drm] nouveau 0000:01:00.0: Unpinning framebuffer(s)...
[ 1572.604899] [drm] nouveau 0000:01:00.0: Evicting buffers...
[ 1572.605288] sdhci-pci 0000:06:0b.3: PCI INT D disabled
[ 1572.605592] ata_piix 0000:00:1f.1: PCI INT B disabled
[ 1572.605611] ehci_hcd 0000:00:1d.7: PCI INT A disabled
[ 1572.605629] uhci_hcd 0000:00:1d.2: PCI INT C disabled
[ 1572.605641] uhci_hcd 0000:00:1d.1: PCI INT B disabled
[ 1572.605653] uhci_hcd 0000:00:1d.0: PCI INT A disabled
[ 1572.605680] pciehp 0000:00:1c.1:pcie04: pciehp_suspend ENTRY
[ 1572.605721] ehci_hcd 0000:00:1a.7: PCI INT C disabled
[ 1572.605733] uhci_hcd 0000:00:1a.1: PCI INT B disabled
[ 1572.605745] uhci_hcd 0000:00:1a.0: PCI INT A disabled
[ 1572.609192] e1000e 0000:00:19.0: PCI INT A disabled
[ 1572.609200] e1000e 0000:00:19.0: PME# enabled
[ 1572.609223] e1000e 0000:00:19.0: wake-up capability enabled by ACPI
[ 1572.650601] [drm] nouveau 0000:01:00.0: Idling channels...
[ 1572.651311] [drm] nouveau 0000:01:00.0: Suspending GPU objects...
[ 1572.950922] PM: suspend of drv:sd dev:0:0:0:0 complete after 501.779 msecs
[ 1572.950935] PM: suspend of drv:scsi dev:target0:0:0 complete after 501.759 msecs
[ 1572.950955] PM: suspend of drv:scsi dev:host0 complete after 480.647 msecs
[ 1572.964074] PM: suspend of drv:ahci dev:0000:00:1f.2 complete after 358.770 msecs
[ 1573.016195] snd_hda_intel 0000:00:1b.0: PCI INT A disabled
[ 1573.032102] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D3
[ 1573.032112] PM: suspend of drv:snd_hda_intel dev:0000:00:1b.0 complete after 426.413 msecs
[ 1574.338681] [drm] nouveau 0000:01:00.0: And we're gone!
[ 1574.338743] nouveau 0000:01:00.0: PCI INT A disabled
[ 1574.352615] nouveau 0000:01:00.0: power state changed by ACPI to D3
[ 1574.352629] PM: suspend of drv:nouveau dev:0000:01:00.0 complete after 1747.779 msecs
[ 1574.352676] PM: suspend of drv:pcieport dev:0000:00:01.0 complete after 1742.934 msecs
[ 1574.352715] PM: suspend of drv: dev:pci0000:00 complete after 1742.895 msecs
[ 1574.352759] PM: suspend of devices complete after 1904.322 msecs
[ 1574.352762] PM: suspend devices took 1.904 seconds
[ 1574.368312] ehci_hcd 0000:00:1d.7: PME# enabled
[ 1574.368338] ehci_hcd 0000:00:1d.7: wake-up capability enabled by ACPI
[ 1574.384183] uhci_hcd 0000:00:1d.2: wake-up capability enabled by ACPI
[ 1574.384293] uhci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[ 1574.384349] ehci_hcd 0000:00:1a.7: PME# enabled
[ 1574.384366] ehci_hcd 0000:00:1a.7: wake-up capability enabled by ACPI
[ 1574.400246] uhci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI
[ 1574.416284] PM: late suspend of devices complete after 63.517 msecs
[ 1574.417054] ACPI: Preparing to enter system sleep state S3
[ 1575.128576] PM: Saving platform NVS memory
[ 1575.128580] Disabling non-boot CPUs ...
[ 1575.232113] CPU 1 is now offline
[ 1575.232626] ACPI: Low-level resume complete
[ 1575.232626] PM: Restoring platform NVS memory
[ 1575.232626] CPU0: Thermal monitoring handled by SMI
[ 1575.232626] Enabling non-boot CPUs ...
[ 1575.232626] Booting Node 0 Processor 1 APIC 0x1
[ 1575.232626] smpboot cpu 1: start_ip = 9b000
[ 1575.130080] Initializing CPU#1
[ 1575.130080] Calibrating delay loop (skipped) already calibrated this CPU
[ 1575.130080] CPU1: Thermal monitoring handled by SMI
[ 1575.246608] NMI watchdog enabled, takes one hw-pmu counter.
[ 1575.248151] CPU1 is up
[ 1575.250987] ACPI: Waking up from system sleep state S3
[ 1575.251108] ACPI: \_SB_.PCI0.FNC2.PRT2 - docking
[ 1575.252142] ACPI: Unable to dock!
[ 1575.252326] pcieport 0000:00:01.0: restoring config space at offset 0xf (was 0x801ff, writing 0x8010a)
[ 1575.252361] mei 0000:00:03.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10a)
[ 1575.252375] mei 0000:00:03.0: restoring config space at offset 0x1 (was 0x100006, writing 0x180006)
[ 1575.252398] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
[ 1575.252423] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100007)
[ 1575.252444] uhci_hcd 0000:00:1a.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10a)
[ 1575.252491] uhci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[ 1575.252539] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x3ff, writing 0x30b)
[ 1575.252706] ehci_hcd 0000:00:1a.7: wake-up capability disabled by ACPI
[ 1575.252712] ehci_hcd 0000:00:1a.7: PME# disabled
[ 1575.252789] pcieport 0000:00:1c.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
[ 1575.252806] pcieport 0000:00:1c.0: restoring config space at offset 0x7 (was 0xf0, writing 0x200000f0)
[ 1575.252876] pcieport 0000:00:1c.1: restoring config space at offset 0xf (was 0x2ff, writing 0x20a)
[ 1575.252892] pcieport 0000:00:1c.1: restoring config space at offset 0x7 (was 0x2000a0a0, writing 0xa0a0)
[ 1575.252956] pcieport 0000:00:1c.2: restoring config space at offset 0xf (was 0x3ff, writing 0x30b)
[ 1575.253021] uhci_hcd 0000:00:1d.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
[ 1575.253064] uhci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[ 1575.253073] uhci_hcd 0000:00:1d.1: restoring config space at offset 0xf (was 0x2ff, writing 0x20b)
[ 1575.253107] uhci_hcd 0000:00:1d.2: restoring config space at offset 0xf (was 0x3ff, writing 0x30b)
[ 1575.253149] uhci_hcd 0000:00:1d.2: wake-up capability disabled by ACPI
[ 1575.253167] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
[ 1575.253217] ehci_hcd 0000:00:1d.7: wake-up capability disabled by ACPI
[ 1575.253223] ehci_hcd 0000:00:1d.7: PME# disabled
[ 1575.253321] ata_piix 0000:00:1f.1: restoring config space at offset 0xf (was 0x2ff, writing 0x20b)
[ 1575.253346] ata_piix 0000:00:1f.1: restoring config space at offset 0x1 (was 0x2800001, writing 0x2880005)
[ 1575.253371] ahci 0000:00:1f.2: restoring config space at offset 0xf (was 0x3ff, writing 0x30b)
[ 1575.253395] ahci 0000:00:1f.2: restoring config space at offset 0x1 (was 0x2b00403, writing 0x2b00407)
[ 1575.253450] nouveau 0000:01:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10a)
[ 1575.253478] nouveau 0000:01:00.0: restoring config space at offset 0x1 (was 0x100003, writing 0x100007)
[ 1575.253551] iwl4965 0000:02:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10a)
[ 1575.253588] iwl4965 0000:02:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xff9fe004)
[ 1575.253602] iwl4965 0000:02:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100006)
[ 1575.253831] sdhci-pci 0000:06:0b.3: restoring config space at offset 0x1 (was 0x2100002, writing 0x2100006)
[ 1575.254705] PM: early resume of devices complete after 2.546 msecs
[ 1575.254849] mei 0000:00:03.0: irq 45 for MSI/MSI-X
[ 1575.254888] e1000e 0000:00:19.0: wake-up capability disabled by ACPI
[ 1575.254896] e1000e 0000:00:19.0: PME# disabled
[ 1575.254902] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1575.254913] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1575.254950] usb usb3: root hub lost power or was reset
[ 1575.254967] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1575.254978] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1575.255012] usb usb4: root hub lost power or was reset
[ 1575.255020] e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
[ 1575.255032] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1575.255040] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1575.255101] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 1575.255107] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 1575.255113] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 1575.255118] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0
[ 1575.255124] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1575.255132] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 1575.255189] snd_hda_intel 0000:00:1b.0: irq 48 for MSI/MSI-X
[ 1575.255250] pciehp 0000:00:1c.1:pcie04: pciehp_resume ENTRY
[ 1575.255270] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1575.255278] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1575.255304] usb usb5: root hub lost power or was reset
[ 1575.255319] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1575.255326] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1575.255352] usb usb6: root hub lost power or was reset
[ 1575.255367] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1575.255374] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1575.255401] usb usb7: root hub lost power or was reset
[ 1575.255416] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1575.255424] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1575.255459] pci 0000:00:1e.0: setting latency timer to 64
[ 1575.255474] ata_piix 0000:00:1f.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1575.255480] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1575.255503] ahci 0000:00:1f.2: setting latency timer to 64
[ 1575.255537] [drm] nouveau 0000:01:00.0: We're back, enabling device...
[ 1575.255920] nouveau 0000:01:00.0: power state changed by ACPI to D0
[ 1575.255926] nouveau 0000:01:00.0: power state changed by ACPI to D0
[ 1575.255933] nouveau 0000:01:00.0: power state changed by ACPI to D0
[ 1575.255938] nouveau 0000:01:00.0: power state changed by ACPI to D0
[ 1575.255945] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1575.255951] nouveau 0000:01:00.0: setting latency timer to 64
[ 1575.255955] [drm] nouveau 0000:01:00.0: POSTing device...
[ 1575.255958] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xC377
[ 1575.265387] iwl4965 0000:02:00.0: RF_KILL bit toggled to disable radio.
[ 1575.265438] ata5: port disabled--ignoring
[ 1575.265460] sdhci-pci 0000:06:0b.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 1575.279451] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xC6C3
[ 1575.305375] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xD118
[ 1575.305409] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xD20A
[ 1575.306496] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xD404
[ 1575.306499] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xD469
[ 1575.320116] firewire_core: skipped bus generations, destroying all nodes
[ 1575.324030] sd 0:0:0:0: [sda] Starting disk
[ 1575.326355] [drm] nouveau 0000:01:00.0: Restoring GPU objects...
[ 1575.384044] PM: resume of drv:hub dev:3-0:1.0 complete after 111.998 msecs
[ 1575.384053] PM: resume of drv: dev:ep_00 complete after 107.915 msecs
[ 1575.384061] PM: resume of drv: dev:ep_81 complete after 107.945 msecs
[ 1575.402063] PM: resume of drv:hub dev:4-0:1.0 complete after 109.978 msecs
[ 1575.402073] PM: resume of drv: dev:ep_00 complete after 109.978 msecs
[ 1575.402079] PM: resume of drv: dev:ep_81 complete after 109.989 msecs
[ 1575.436038] PM: resume of drv:hub dev:7-0:1.0 complete after 115.961 msecs
[ 1575.436046] PM: resume of drv: dev:ep_00 complete after 115.913 msecs
[ 1575.436052] PM: resume of drv: dev:ep_81 complete after 115.962 msecs
[ 1575.494350] PM: resume of drv:button dev:PNP0C0D:00 complete after 202.046 msecs
[ 1575.500091] PM: resume of drv:mei dev:0000:00:03.0 complete after 245.272 msecs
[ 1575.516052] PM: resume of drv:hub dev:5-0:1.0 complete after 223.941 msecs
[ 1575.516060] PM: resume of drv: dev:ep_00 complete after 216.031 msecs
[ 1575.516085] PM: resume of drv:hub dev:2-0:1.0 complete after 250.508 msecs
[ 1575.516093] PM: resume of drv: dev:ep_00 complete after 250.508 msecs
[ 1575.516099] PM: resume of drv: dev:ep_81 complete after 218.479 msecs
[ 1575.516106] PM: resume of drv: dev:ep_81 complete after 250.525 msecs
[ 1575.532053] PM: resume of drv:hub dev:6-0:1.0 complete after 224.002 msecs
[ 1575.532061] PM: resume of drv: dev:ep_00 complete after 216.041 msecs
[ 1575.532077] PM: resume of drv: dev:ep_81 complete after 224.009 msecs
[ 1575.556290] [drm] nouveau 0000:01:00.0: Reinitialising engines...
[ 1575.558352] [drm] nouveau 0000:01:00.0: Restoring mode...
[ 1575.597679] PM: resume of drv:nouveau dev:0000:01:00.0 complete after 342.141 msecs
[ 1575.618008] PM: resume of drv:e1000e dev:0000:00:19.0 complete after 363.139 msecs
[ 1575.636067] usb 5-1: reset full-speed USB device number 2 using uhci_hcd
[ 1575.660557] ata4.00: ACPI cmd ef/03:0c:00:00:00:00 (SET FEATURES) filtered out
[ 1575.660561] ata4.00: ACPI cmd ef/03:42:00:00:00:00 (SET FEATURES) filtered out
[ 1575.676508] ata4.00: configured for UDMA/33
[ 1575.772098] ata3: SATA link down (SStatus 0 SControl 300)
[ 1575.820095] firewire_core: rediscovered device fw0
[ 1575.884092] usb 6-1: reset full-speed USB device number 2 using uhci_hcd
[ 1576.000091] PM: resume of drv:hub dev:5-1:1.0 complete after 668.028 msecs
[ 1576.000112] PM: resume of drv: dev:ep_00 complete after 660.089 msecs
[ 1576.000122] PM: resume of drv: dev:ep_81 complete after 664.099 msecs
[ 1576.039081] PM: resume of drv: dev:ep_00 complete after 683.038 msecs
[ 1576.039106] PM: resume of drv:usb dev:6-1:1.0 complete after 695.063 msecs
[ 1576.039144] PM: resume of drv: dev:ep_83 complete after 683.121 msecs
[ 1576.039153] PM: resume of drv: dev:ep_02 complete after 687.131 msecs
[ 1576.039162] PM: resume of drv: dev:ep_81 complete after 691.138 msecs
[ 1576.240114] PM: resume of drv:tpm_tis dev:00:0a complete after 744.830 msecs
[ 1576.313050] serial 00:0c: activated
[ 1576.314152] usb 5-1.4: reset low-speed USB device number 5 using uhci_hcd
[ 1576.623158] PM: resume of drv: dev:ep_00 complete after 1226.920 msecs
[ 1576.623179] PM: resume of drv:usbhid dev:5-1.4:1.0 complete after 1235.155 msecs
[ 1576.623207] PM: resume of drv: dev:ep_81 complete after 1231.184 msecs
[ 1576.677145] usb 5-1.2: reset full-speed USB device number 4 using uhci_hcd
[ 1576.764060] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1576.765100] ata1.00: unexpected _GTF length (8)
[ 1576.772460] ata1.00: unexpected _GTF length (8)
[ 1576.772892] ata1.00: configured for UDMA/100
[ 1576.803623] PM: resume of drv:sd dev:0:0:0:0 complete after 1479.594 msecs
[ 1576.803633] PM: resume of drv:scsi_device dev:0:0:0:0 complete after 1475.611 msecs
[ 1576.803647] PM: resume of drv:scsi_disk dev:0:0:0:0 complete after 488.484 msecs
[ 1576.806155] usblp 5-1.2:1.0: no reset_resume for driver usblp?
[ 1576.806283] usblp0: removed
[ 1576.806297] PM: resume of drv: dev:ep_00 complete after 1422.224 msecs
[ 1576.806319] PM: resume of drv:usb dev:5-1.2:1.0 complete after 1422.268 msecs
[ 1576.806351] PM: resume of drv: dev:ep_02 complete after 1422.284 msecs
[ 1576.806357] PM: resume of drv: dev:ep_81 complete after 1422.298 msecs
[ 1576.853154] usb 5-1.1: reset full-speed USB device number 3 using uhci_hcd
[ 1576.964156] PM: resume of drv: dev:ep_00 complete after 1592.114 msecs
[ 1576.964181] PM: resume of drv:usb-storage dev:5-1.1:1.0 complete after 1600.147 msecs
[ 1576.964214] PM: resume of drv:scsi dev:host5 complete after 1588.192 msecs
[ 1576.964223] PM: resume of drv: dev:ep_02 complete after 1592.201 msecs
[ 1576.964236] PM: resume of drv: dev:ep_81 complete after 1596.204 msecs
[ 1576.964247] PM: resume of drv:scsi dev:target5:0:0 complete after 1567.983 msecs
[ 1576.964257] PM: resume of drv:scsi_host dev:host5 complete after 1584.233 msecs
[ 1576.964261] PM: resume of drv:sd dev:5:0:0:0 complete after 1564.221 msecs
[ 1576.964276] PM: resume of drv:scsi_device dev:5:0:0:0 complete after 1562.204 msecs
[ 1576.964282] PM: resume of drv:scsi_disk dev:5:0:0:0 complete after 160.581 msecs
[ 1577.104246] PM: resume of devices complete after 1849.489 msecs
[ 1577.109263] usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3404
[ 1577.109405] PM: resume devices took 1.856 seconds
[ 1577.109447] PM: Finishing wakeup.
[ 1577.109449] Restarting tasks ... done.
[ 1577.111947] video LNXVIDEO:00: Restoring backlight state
[ 1577.262656] mmc0: new high speed SDHC card at address 1234
[ 1577.264484] mmcblk0: mmc0:1234 SA04G 3.63 GiB
[ 1577.269016] mmcblk0: p1
[ 1578.213503] usblp0: removed
[ 1578.225864] usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x03F0 pid 0x3404
[ 1578.660336] e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
[ 1578.716130] e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
[ 1578.716418] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1580.132961] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 1580.132966] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 1580.133148] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1591.072080] eth0: no IPv6 routers present
[ 1604.564184] mei 0000:00:03.0: unexpected reset.
[ 1604.565710] watchdog: only one watchdog can use /dev/watchdog.
[ 1604.565720] watchdog: error registering /dev/watchdog (err=-16).
[ 1604.565726] mei: unable to register watchdog device.
[ 3391.729629] usb 5-1.3: new full-speed USB device number 6 using uhci_hcd
[ 3391.830620] usb 5-1.3: not running at top speed; connect to a high speed hub
[ 3391.851919] scsi6 : usb-storage 5-1.3:1.0
[ 3392.856755] scsi 6:0:0:0: Direct-Access SanDisk Cruzer 8.02 PQ: 0 ANSI: 0 CCS
[ 3392.858617] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 3392.869557] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 3393.976586] sd 6:0:0:0: [sdc] 15695871 512-byte logical blocks: (8.03 GB/7.48 GiB)
[ 3393.982574] sd 6:0:0:0: [sdc] No Caching mode page present
[ 3393.982585] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 3393.995685] sd 6:0:0:0: [sdc] No Caching mode page present
[ 3393.995696] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 3394.006847] sdc: sdc1
[ 3808.884222] pcmcia_socket pcmcia_socket0: pccard: PCMCIA card inserted into slot 0
[ 3808.884710] pcmcia 0.0: pcmcia: registering new device pcmcia0.0 (IRQ: 3)
zippytex@zippytex-TECRA-M9 ~ $
zippytex@zippytex-TECRA-M9 ~ $ sudo modprobe pata_pcmcia
zippytex@zippytex-TECRA-M9 ~ $
zippytex@zippytex-TECRA-M9 ~ $ lspcmcia
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:06:0b.0)
Socket 0 Device 0: [-- no driver --] (bus ID: 0.0)
zippytex@zippytex-TECRA-M9 ~ $
zippytex
Level 1
Level 1
 
Posts: 43
Joined: Mon Jul 11, 2011 3:22 pm

Linux Mint is funded by ads and donations.
 

Return to Hardware Support

Who is online

Users browsing this forum: No registered users and 11 guests