Lost screen resolution

Questions about hardware,drivers and peripherals
Forum rules
Before you post please read this

Lost screen resolution

Postby badmotor on Thu Jun 05, 2008 3:36 pm

I am using Daryna on an Acer Veriton desktop (fairly recent). Every couple of times I log in, my screen resolution changes to something lower and I have to reset it and reboot. If it helps, I have desktop settings set to 'Normal'. Anyone have any ideas?

I don't think I have a separate graphics card.
badmotor
Level 4
Level 4
 
Posts: 371
Joined: Fri May 02, 2008 7:40 pm
Location: New Zealand.

Linux Mint is funded by ads and donations.
 

Re: Lost screen resolution

Postby 67GTA on Thu Jun 05, 2008 3:59 pm

Post the output of
Code: Select all
lspci
from a terminal, and post a copy of your /etc/X11/xorg.conf file. What resolution are you wanting?
"The only thing necessary for the triumph of evil is for good men to do nothing." Edmund Burke
User avatar
67GTA
Level 6
Level 6
 
Posts: 1301
Joined: Wed Jun 06, 2007 9:49 pm
Location: Kentucky, USA

Re: Lost screen resolution

Postby badmotor on Fri Jun 06, 2008 2:40 am

Hi :

00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02)
00:02.1 Display controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GH (ICH7DH) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller

... and xorg.conf:

# xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg

Section "Files"
EndSection

Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection

Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection

Section "InputDevice"
Driver "wacom"
Identifier "stylus"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4"# Tablet PC ONLY
EndSection

Section "InputDevice"
Driver "wacom"
Identifier "eraser"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4"# Tablet PC ONLY
EndSection

Section "InputDevice"
Driver "wacom"
Identifier "cursor"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4"# Tablet PC ONLY
EndSection

Section "Device"
Identifier "Intel Corporation Integrated Graphics Controller"
Boardname "intel"
Busid "PCI:0:2:0"
Driver "intel"
Screen 0
EndSection

Section "Monitor"
Identifier "HIQ T91D"
Vendorname "Plug 'n' Play"
Modelname "Plug 'n' Play"
modeline "640x480@60" 25.2 640 656 752 800 480 490 492 525 -vsync -hsync
modeline "640x480@72" 31.5 640 664 704 832 480 489 491 520 -vsync -hsync
modeline "640x480@75" 31.5 640 656 720 840 480 481 484 500 -vsync -hsync
modeline "800x600@56" 36.0 800 824 896 1024 600 601 603 625 +hsync +vsync
modeline "800x600@72" 50.0 800 856 976 1040 600 637 643 666 +hsync +vsync
modeline "800x600@75" 49.5 800 816 896 1056 600 601 604 625 +hsync +vsync
modeline "800x600@60" 40.0 800 840 968 1056 600 601 605 628 +hsync +vsync
modeline "832x624@75" 57.284 832 864 928 1152 624 625 628 667 -vsync -hsync
modeline "1024x768@75" 78.8 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
modeline "1024x768@70" 75.0 1024 1048 1184 1328 768 771 777 806 -vsync -hsync
modeline "1024x768@60" 65.0 1024 1048 1184 1344 768 771 777 806 -vsync -hsync
modeline "1152x864@75" 108.0 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
modeline "1280x1024@75" 135.0 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
modeline "1280x960@60" 102.1 1280 1360 1496 1712 960 961 964 994 -hsync +vsync
modeline "1280x1024@60" 108.0 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
modeline "1280x960@75" 129.86 1280 1368 1504 1728 960 961 964 1002 -hsync +vsync
modeline "1400x1050@60" 122.61 1400 1488 1640 1880 1050 1051 1054 1087 -hsync +vsync
modeline "1400x1050@75" 155.85 1400 1496 1648 1896 1050 1051 1054 1096 -hsync +vsync
modeline "1600x1200@65" 175.5 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
modeline "1600x1200@60" 162.0 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
modeline "1792x1344@60" 204.8 1792 1920 2120 2448 1344 1345 1348 1394 -hsync +vsync
Gamma 1.0
EndSection

Section "Screen"
Identifier "Default Screen"
Device "Intel Corporation Integrated Graphics Controller"
Monitor "HIQ T91D"
Defaultdepth 24
SubSection "Display"
Depth 24
Virtual 1792 1344
Modes "1280x1024@60" "1280x960@75" "1280x960@60" "1400x1050@60" "1280x1024@75" "1400x1050@75" "1152x864@75" "1600x1200@65" "1024x768@60" "1600x1200@60" "1024x768@70" "1792x1344@60" "1024x768@75" "832x624@75" "800x600@60" "800x600@75" "800x600@72" "800x600@56" "640x480@75" "640x480@72" "640x480@60"
EndSubSection
EndSection

Section "ServerLayout"
Identifier "Default Layout"
screen 0 "Default Screen" 0 0
Inputdevice "Generic Keyboard"
Inputdevice "Configured Mouse"

# Uncomment if you have a wacom tablet
# InputDevice "stylus" "SendCoreEvents"
# InputDevice "cursor" "SendCoreEvents"
# InputDevice "eraser" "SendCoreEvents"
EndSection
Section "Module"
Load "glx"
Load "GLcore"
Load "v4l"
EndSection
Section "device" #
Identifier "device1"
Boardname "VESA driver (generic)"
Busid "PCI:0:2:1"
Driver "vesa"
Screen 0
EndSection
Section "screen" #
Identifier "screen1"
Device "device1"
Defaultdepth 24
Monitor "monitor1"
SubSection "Display"
Depth 24
Modes "640x480@60" "640x480@72" "640x480@75" "800x600@56" "800x600@72" "800x600@75" "800x600@60" "832x624@75" "1024x768@75" "1024x768@70" "1024x768@60" "1152x864@75" "1280x1024@75" "1280x960@60" "1280x1024@60" "1280x960@75" "1400x1050@60" "1400x1050@75" "1600x1200@65" "1600x1200@60" "1792x1344@60"
EndSubSection
EndSection
Section "monitor" #
Identifier "monitor1"
Vendorname "Plug 'n' Play"
Modelname "Plug 'n' Play"
modeline "640x480@60" 25.2 640 656 752 800 480 490 492 525 -vsync -hsync
modeline "640x480@72" 31.5 640 664 704 832 480 489 491 520 -vsync -hsync
modeline "640x480@75" 31.5 640 656 720 840 480 481 484 500 -vsync -hsync
modeline "800x600@56" 36.0 800 824 896 1024 600 601 603 625 +hsync +vsync
modeline "800x600@72" 50.0 800 856 976 1040 600 637 643 666 +hsync +vsync
modeline "800x600@75" 49.5 800 816 896 1056 600 601 604 625 +hsync +vsync
modeline "800x600@60" 40.0 800 840 968 1056 600 601 605 628 +hsync +vsync
modeline "832x624@75" 57.284 832 864 928 1152 624 625 628 667 -vsync -hsync
modeline "1024x768@75" 78.8 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
modeline "1024x768@70" 75.0 1024 1048 1184 1328 768 771 777 806 -vsync -hsync
modeline "1024x768@60" 65.0 1024 1048 1184 1344 768 771 777 806 -vsync -hsync
modeline "1152x864@75" 108.0 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
modeline "1280x1024@75" 135.0 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
modeline "1280x960@60" 102.1 1280 1360 1496 1712 960 961 964 994 -hsync +vsync
modeline "1280x1024@60" 108.0 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
modeline "1280x960@75" 129.86 1280 1368 1504 1728 960 961 964 1002 -hsync +vsync
modeline "1400x1050@60" 122.61 1400 1488 1640 1880 1050 1051 1054 1087 -hsync +vsync
modeline "1400x1050@75" 155.85 1400 1496 1648 1896 1050 1051 1054 1096 -hsync +vsync
modeline "1600x1200@65" 175.5 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
modeline "1600x1200@60" 162.0 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
modeline "1792x1344@60" 204.8 1792 1920 2120 2448 1344 1345 1348 1394 -hsync +vsync
Gamma 1.0
EndSection
Section "ServerFlags"
EndSection

I want the resolution to stay at 1280x1024

Cheers!
badmotor
Level 4
Level 4
 
Posts: 371
Joined: Fri May 02, 2008 7:40 pm
Location: New Zealand.

Re: Lost screen resolution

Postby 67GTA on Fri Jun 06, 2008 2:48 am

Man that's a lot of modelines! The first I would try is to get rid of all of the extra resolution settings except the ones for 1280x1024.
"The only thing necessary for the triumph of evil is for good men to do nothing." Edmund Burke
User avatar
67GTA
Level 6
Level 6
 
Posts: 1301
Joined: Wed Jun 06, 2007 9:49 pm
Location: Kentucky, USA

Re: Lost screen resolution

Postby badmotor on Fri Jun 06, 2008 6:10 am

OK.

edit: actually, I might just wait for Mint 5 and see if it still does it then.
badmotor
Level 4
Level 4
 
Posts: 371
Joined: Fri May 02, 2008 7:40 pm
Location: New Zealand.


Return to Hardware Support

Who is online

Users browsing this forum: bartszu and 14 guests