Nokia GPRS

Questions about hardware,drivers and peripherals
Forum rules
Before you post please read this

Nokia GPRS

Postby loneowais on Thu Aug 02, 2007 9:32 am

I did it on a nokia n80, n73, 6230(somethinsimilar..is a folder java phone), 7610, 6630 & 6680....

This is how to do it...

Connect your phone via datacable
open terminal & type

lsusb

now u will get the following output

owais@owais-desktop:~$ lsusb
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 004: ID 0421:0445 Nokia Mobile Phones
Bus 001 Device 002: ID 046d:092f Logitech, Inc.
Bus 001 Device 001: ID 0000:0000
owais@owais-desktop:~$


it is on my compter,ur will not be exactly the same...

Now note the line in which NOkia Mobile Phones is written...it has two number one is 0421 & other is 0445...we'll take these numbers as 0x421 & 0x445

0421 is the Vendor ID & 0445 is the Product ID

Now enter this comand.

sudo /sbin/modprobe usbserial vendor=0x(vid) product=0x(pid)

eg, in my case::: sudo /sbin/modprobe usbserial vendor=0×421 product=0×445

Now enter this command

wvdialconf create
u'll get a long output which will be like

Scanning your serial ports for a modem.
Port Scan: S0 S1 S2 S3
WvModem: Cannot get information for serial port.
ttyACM0: ATQ0 V1 E1 — OK
ttyACM0: ATQ0 V1 E1 Z — OK
ttyACM0: ATQ0 V1 E1 S0=0 — OK
ttyACM0: ATQ0 V1 E1 S0=0 &C1 — OK
ttyACM0: ATQ0 V1 E1 S0=0 &C1 &D2 — OK
ttyACM0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
ttyACM0: Modem Identifier: ATI — Nokia
ttyACM0: Speed 4800: AT — OK
ttyACM0: Speed 9600: AT — OK
ttyACM0: Speed 19200: AT — OK
ttyACM0: Speed 38400: AT — OK
ttyACM0: Speed 57600: AT — OK
ttyACM0: Speed 115200: AT — OK
ttyACM0: Speed 230400: AT — OK
ttyACM0: Speed 460800: AT — OK
ttyACM0: Max speed is 460800; that should be safe.
ttyACM0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
Found an USB modem on /dev/ttyACM0.
Modem configuration written to create.
ttyACM0: Speed 460800; init “ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0″

NOw.. notice the output says that there is a modem at /dev/ttyACM0 & max speed is 460800

now enter this command

sudo gedit /etc/wvdial.conf

A file will open in text editor...now delete everything in that file & paste the following there

[Dialer Defaults]
Modem = Your Modem Name(eg, /dev/ttyACM0 in my case)
Baud = ur max speed(460800 in my case)
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Modem Type = Analog Modem
Phone = *99#
Username = username
Password = password
Stupid Mode = 1

save the file & you are done


NOw whenevr u need to connect...open terminal & type wvdial,,wait till some sort of IP adress is displayed like

pppd: �[06][06][08]` [06][08]
primary DNS address 218.248.240.135
pppd: �[06][06][08]` [06][08]
secondary DNS address 218.248.240.79
pppd: �[06][06][08]` [06][08]

Now you are connected....hit cntrl+c to dissconnect...



U can also create a laucher on desktop(application in terminal) & keep the command as wvdial..now double click it & u r connected
loneowais
Level 1
Level 1
 
Posts: 10
Joined: Tue Jun 26, 2007 9:18 am

Linux Mint is funded by ads and donations.
 

Postby Boo on Sun Aug 05, 2007 10:08 pm

Thank for the informational post.

This should go into the Tips and Tricks area too.

:D
Image
Now where was i going? Oh yes, crazy!
User avatar
Boo
Level 8
Level 8
 
Posts: 2364
Joined: Mon Mar 26, 2007 7:48 am


Return to Hardware Support

Who is online

Users browsing this forum: No registered users and 14 guests