I've got a dell d505 with linux mint installed. It's been working fine for quite sometime and I use the wireless network at home and at work without any problems. Until today that is.
Suddenly despite seeing my wireless network I cannot connect. On the same laptop on different partitions I also have a ubuntu and an xp installation - I cannot connect to my wireless network on either of these.
I have another laptop which connects to my wireless network no problems.
I'm almost certain that the wireless card in the dell is broken, but is there any diagnostic program I can run which will confirm this? Is it fixable or should I just go out and buy a new one?
Thanks
Is my wireless card broken
Forum rules
Before you post read how to get help. Topics in this forum are automatically closed 6 months after creation.
Before you post read how to get help. Topics in this forum are automatically closed 6 months after creation.
-
bzzzzz
Is my wireless card broken
Last edited by LockBot on Wed Dec 28, 2022 7:16 am, edited 1 time in total.
Reason: Topic automatically closed 6 months after creation. New replies are no longer allowed.
Reason: Topic automatically closed 6 months after creation. New replies are no longer allowed.
-
rich_roast
Re: Is my wireless card broken
Errors on trying to connect wirelessly are logged in your syslog, located at /var/log/syslog. Perusing that might throw some light on to what precisely is causing the device to give up, although it's not a hardware diagnostic persay. Might be a place to start?
-
Aging Technogeek
Re: Is my wireless card broken
As a general rule, if networking doesn't work in three different OS, suspect the hardware. Given the symptoms you describe, I would think that your wireless transmitter is gone. Your receiver works, that's why you can see your network, but with a dead transmitter you will never connect.
Laptop repairs can be difficult. They are normally difficult to get into and very densely packed if you do get in. I would not recommend that anyone other than an trained technician attempt to do more than replace a hard drive or a ram stick.
Laptop repairs can be difficult. They are normally difficult to get into and very densely packed if you do get in. I would not recommend that anyone other than an trained technician attempt to do more than replace a hard drive or a ram stick.
Re: Is my wireless card broken
Are you sure the wifi is enabled in the BIOS and switched on at the switch or Fn toggle?
FWIW replacment mini-pci card for this model on ebay at $11.99 and they are relatively easy to fit on most Dell models.
FWIW replacment mini-pci card for this model on ebay at $11.99 and they are relatively easy to fit on most Dell models.
[Edit] your original post and add [SOLVED] once your question is resolved.
“The people are my God” stressing the factor determining man’s destiny lies within man not in anything outside man, and thereby defining man as the dominator and remoulder of the world.
“The people are my God” stressing the factor determining man’s destiny lies within man not in anything outside man, and thereby defining man as the dominator and remoulder of the world.
-
bzzzzz
Re: Is my wireless card broken
Turned on laptop today and its all working.
I looked at the syslog file
I'm not really sure what this tells me. On trying the different Operating systems I did shut down my laptop and restart on several occasions. I am not going to post this as solved as it may be something which is going to be temperamental. I have bought a new wireless card off ebay and we'll see if that makes any difference.
Thanks for help so far
I looked at the syslog file
Code: Select all
Apr 24 20:07:27 QUARTZ kernel: [ 14.389105] Boot video device is 0000:00:02.0
Apr 24 20:07:27 QUARTZ kernel: [ 14.389172] PCI: Firmware left 0000:01:08.0 e100 interrupts enabled, disabling
Apr 24 20:07:27 QUARTZ kernel: [ 14.389559] isapnp: Scanning for PnP cards...
Apr 24 20:07:27 QUARTZ kernel: [ 14.742134] isapnp: No Plug & Play device found
Apr 24 20:07:27 QUARTZ kernel: [ 14.789282] Real Time Clock Driver v1.12ac
Apr 24 20:07:27 QUARTZ kernel: [ 14.789422] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Apr 24 20:07:27 QUARTZ kernel: [ 14.789548] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Apr 24 20:07:27 QUARTZ kernel: [ 14.789724] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Apr 24 20:07:27 QUARTZ kernel: [ 14.790572] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Apr 24 20:07:27 QUARTZ kernel: [ 14.791076] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
Apr 24 20:07:27 QUARTZ kernel: [ 14.791081] PCI: setting IRQ 5 as level-triggered
Apr 24 20:07:27 QUARTZ kernel: [ 14.791085] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
Apr 24 20:07:27 QUARTZ kernel: [ 14.791097] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
Apr 24 20:07:27 QUARTZ kernel: [ 14.791982] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
Apr 24 20:07:27 QUARTZ kernel: [ 14.792088] input: Macintosh mouse button emulation as /devices/virtual/input/input0
Apr 24 20:07:27 QUARTZ kernel: [ 14.792260] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
Apr 24 20:07:27 QUARTZ kernel: [ 14.797356] serio: i8042 KBD port at 0x60,0x64 irq 1
Apr 24 20:07:27 QUARTZ kernel: [ 14.797363] serio: i8042 AUX port at 0x60,0x64 irq 12
Apr 24 20:07:27 QUARTZ kernel: [ 14.800286] mice: PS/2 mouse device common for all mice
Apr 24 20:07:27 QUARTZ kernel: [ 14.800442] EISA: Probing bus 0 at eisa.0
Apr 24 20:07:27 QUARTZ kernel: [ 14.800478] EISA: Detected 0 cards.
Apr 24 20:07:27 QUARTZ kernel: [ 14.800482] cpuidle: using governor ladder
Apr 24 20:07:27 QUARTZ kernel: [ 14.800485] cpuidle: using governor menu
Apr 24 20:07:27 QUARTZ kernel: [ 14.800614] NET: Registered protocol family 1
Apr 24 20:07:27 QUARTZ kernel: [ 14.800660] Using IPI No-Shortcut mode
Apr 24 20:07:27 QUARTZ kernel: [ 14.800709] registered taskstats version 1
Apr 24 20:07:27 QUARTZ kernel: [ 14.800852] Magic number: 6:976:144
Apr 24 20:07:27 QUARTZ kernel: [ 14.801009] hash matches device device:15
Apr 24 20:07:27 QUARTZ kernel: [ 14.801026] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
Apr 24 20:07:27 QUARTZ kernel: [ 14.801029] EDD information not available.
Apr 24 20:07:27 QUARTZ kernel: [ 14.801240] Freeing unused kernel memory: 368k freed
Apr 24 20:07:27 QUARTZ kernel: [ 14.801279] Write protecting the kernel read-only data: 802k
Apr 24 20:07:27 QUARTZ kernel: [ 14.804890] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
Apr 24 20:07:27 QUARTZ kernel: [ 16.122175] fuse init (API version 7.9)
Apr 24 20:07:27 QUARTZ kernel: [ 16.154782] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
Apr 24 20:07:27 QUARTZ kernel: [ 16.154792] ACPI: Processor [CPU0] (supports 8 throttling states)
Apr 24 20:07:27 QUARTZ kernel: [ 16.161139] ACPI: Thermal Zone [THM] (51 C)
Apr 24 20:07:27 QUARTZ kernel: [ 17.108223] usbcore: registered new interface driver usbfs
Apr 24 20:07:27 QUARTZ kernel: [ 17.108259] usbcore: registered new interface driver hub
Apr 24 20:07:27 QUARTZ kernel: [ 17.126144] usbcore: registered new device driver usb
Apr 24 20:07:27 QUARTZ kernel: [ 17.206915] SCSI subsystem initialized
Apr 24 20:07:27 QUARTZ kernel: [ 17.219958] USB Universal Host Controller Interface driver v3.0
Apr 24 20:07:27 QUARTZ kernel: [ 17.220049] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.220066] PCI: Setting latency timer of device 0000:00:1d.0 to 64
Apr 24 20:07:27 QUARTZ kernel: [ 17.220072] uhci_hcd 0000:00:1d.0: UHCI Host Controller
Apr 24 20:07:27 QUARTZ kernel: [ 17.220461] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
Apr 24 20:07:27 QUARTZ kernel: [ 17.220489] uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80
Apr 24 20:07:27 QUARTZ kernel: [ 17.220687] usb usb1: configuration #1 chosen from 1 choice
Apr 24 20:07:27 QUARTZ kernel: [ 17.220721] hub 1-0:1.0: USB hub found
Apr 24 20:07:27 QUARTZ kernel: [ 17.220729] hub 1-0:1.0: 2 ports detected
Apr 24 20:07:27 QUARTZ kernel: [ 17.324316] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.324323] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.324337] PCI: Setting latency timer of device 0000:00:1d.1 to 64
Apr 24 20:07:27 QUARTZ kernel: [ 17.324343] uhci_hcd 0000:00:1d.1: UHCI Host Controller
Apr 24 20:07:27 QUARTZ kernel: [ 17.324377] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
Apr 24 20:07:27 QUARTZ kernel: [ 17.324403] uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000bf40
Apr 24 20:07:27 QUARTZ kernel: [ 17.324573] usb usb2: configuration #1 chosen from 1 choice
Apr 24 20:07:27 QUARTZ kernel: [ 17.324605] hub 2-0:1.0: USB hub found
Apr 24 20:07:27 QUARTZ kernel: [ 17.324613] hub 2-0:1.0: 2 ports detected
Apr 24 20:07:27 QUARTZ kernel: [ 17.343009] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
Apr 24 20:07:27 QUARTZ kernel: [ 17.343015] e100: Copyright(c) 1999-2006 Intel Corporation
Apr 24 20:07:27 QUARTZ kernel: [ 17.347965] libata version 3.00 loaded.
Apr 24 20:07:27 QUARTZ kernel: [ 17.428317] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.428324] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.428339] PCI: Setting latency timer of device 0000:00:1d.2 to 64
Apr 24 20:07:27 QUARTZ kernel: [ 17.428344] uhci_hcd 0000:00:1d.2: UHCI Host Controller
Apr 24 20:07:27 QUARTZ kernel: [ 17.428381] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
Apr 24 20:07:27 QUARTZ kernel: [ 17.428407] uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000bf20
Apr 24 20:07:27 QUARTZ kernel: [ 17.428566] usb usb3: configuration #1 chosen from 1 choice
Apr 24 20:07:27 QUARTZ kernel: [ 17.428599] hub 3-0:1.0: USB hub found
Apr 24 20:07:27 QUARTZ kernel: [ 17.428607] hub 3-0:1.0: 2 ports detected
Apr 24 20:07:27 QUARTZ kernel: [ 17.532418] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.532424] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.532441] PCI: Setting latency timer of device 0000:00:1d.7 to 64
Apr 24 20:07:27 QUARTZ kernel: [ 17.532446] ehci_hcd 0000:00:1d.7: EHCI Host Controller
Apr 24 20:07:27 QUARTZ kernel: [ 17.532484] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
Apr 24 20:07:27 QUARTZ kernel: [ 17.536408] ehci_hcd 0000:00:1d.7: debug port 1
Apr 24 20:07:27 QUARTZ kernel: [ 17.536415] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
Apr 24 20:07:27 QUARTZ kernel: [ 17.536425] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xfaeffc00
Apr 24 20:07:27 QUARTZ kernel: [ 17.563920] usb 1-2: new full speed USB device using uhci_hcd and address 2
Apr 24 20:07:27 QUARTZ kernel: [ 17.575910] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Apr 24 20:07:27 QUARTZ kernel: [ 17.576076] usb usb4: configuration #1 chosen from 1 choice
Apr 24 20:07:27 QUARTZ kernel: [ 17.576112] hub 4-0:1.0: USB hub found
Apr 24 20:07:27 QUARTZ kernel: [ 17.576122] hub 4-0:1.0: 6 ports detected
Apr 24 20:07:27 QUARTZ kernel: [ 17.680516] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.680523] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.705094] e100: eth0: e100_probe: addr 0xfcffd000, irq 11, MAC addr 00:0f:1f:a1:45:2c
Apr 24 20:07:27 QUARTZ kernel: [ 17.705135] ACPI: PCI Interrupt 0000:01:01.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.754897] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[fcfff800-fcffffff] Max Packet=[2048] IR/IT contexts=[4/8]
Apr 24 20:07:27 QUARTZ kernel: [ 17.766367] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
Apr 24 20:07:27 QUARTZ kernel: [ 17.766379] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.766426] PCI: Setting latency timer of device 0000:00:1f.1 to 64
Apr 24 20:07:27 QUARTZ kernel: [ 17.766442] ACPI: PCI interrupt for device 0000:00:1f.1 disabled
Apr 24 20:07:27 QUARTZ kernel: [ 17.773698] ata_piix 0000:00:1f.1: version 2.12
Apr 24 20:07:27 QUARTZ kernel: [ 17.773722] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Apr 24 20:07:27 QUARTZ kernel: [ 17.773769] PCI: Setting latency timer of device 0000:00:1f.1 to 64
Apr 24 20:07:27 QUARTZ kernel: [ 17.775081] scsi0 : ata_piix
Apr 24 20:07:27 QUARTZ kernel: [ 17.775483] scsi1 : ata_piix
Apr 24 20:07:27 QUARTZ kernel: [ 17.776836] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
Apr 24 20:07:27 QUARTZ kernel: [ 17.776840] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
Apr 24 20:07:27 QUARTZ kernel: [ 17.993280] ata1.00: ATA-7: WDC WD1600BEVE-00UYT0, 01.04A01, max UDMA/100
Apr 24 20:07:27 QUARTZ kernel: [ 17.993287] ata1.00: 312581808 sectors, multi 8: LBA48
Apr 24 20:07:27 QUARTZ kernel: [ 18.008967] ata1.00: configured for UDMA/100
Apr 24 20:07:27 QUARTZ kernel: [ 18.164085] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVE-0 01.0 PQ: 0 ANSI: 5
Apr 24 20:07:27 QUARTZ kernel: [ 18.199842] usb 1-2: new full speed USB device using uhci_hcd and address 3
Apr 24 20:07:27 QUARTZ kernel: [ 18.298057] Driver 'sd' needs updating - please use bus_type methods
Apr 24 20:07:27 QUARTZ kernel: [ 18.298172] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
Apr 24 20:07:27 QUARTZ kernel: [ 18.298189] sd 0:0:0:0: [sda] Write Protect is off
Apr 24 20:07:27 QUARTZ kernel: [ 18.298193] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Apr 24 20:07:27 QUARTZ kernel: [ 18.298217] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 24 20:07:27 QUARTZ kernel: [ 18.298281] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
Apr 24 20:07:27 QUARTZ kernel: [ 18.298294] sd 0:0:0:0: [sda] Write Protect is off
Apr 24 20:07:27 QUARTZ kernel: [ 18.298298] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Apr 24 20:07:27 QUARTZ kernel: [ 18.298319] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Apr 24 20:07:27 QUARTZ kernel: [ 18.298324] sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 >
Apr 24 20:07:27 QUARTZ kernel: [ 18.390210] sd 0:0:0:0: [sda] Attached SCSI disk
Apr 24 20:07:27 QUARTZ kernel: [ 18.400917] sd 0:0:0:0: Attached scsi generic sg0 type 0
Apr 24 20:07:27 QUARTZ kernel: [ 18.512654] usb 1-2: configuration #1 chosen from 1 choice
Apr 24 20:07:27 QUARTZ kernel: [ 19.031906] ieee1394: Host added: ID:BUS[0-00:1023] GUID[424fc00006b69030]
Apr 24 20:07:27 QUARTZ kernel: [ 24.243640] kjournald starting. Commit interval 5 seconds
Apr 24 20:07:27 QUARTZ kernel: [ 24.243658] EXT3-fs: mounted filesystem with ordered data mode.
Apr 24 20:07:27 QUARTZ kernel: [ 36.634180] iTCO_vendor_support: vendor-support=0
Apr 24 20:07:27 QUARTZ kernel: [ 36.677709] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
Apr 24 20:07:27 QUARTZ kernel: [ 36.678209] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x0860)
Apr 24 20:07:27 QUARTZ kernel: [ 36.678265] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Apr 24 20:07:27 QUARTZ kernel: [ 36.874181] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Apr 24 20:07:27 QUARTZ kernel: [ 36.927752] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Apr 24 20:07:27 QUARTZ kernel: [ 37.006147] Linux agpgart interface v0.102
Apr 24 20:07:27 QUARTZ kernel: [ 37.062249] input: PC Speaker as /devices/platform/pcspkr/input/input2
Apr 24 20:07:27 QUARTZ kernel: [ 37.146185] agpgart: Detected an Intel 855GM Chipset.
Apr 24 20:07:27 QUARTZ kernel: [ 37.146376] agpgart: Detected 8060K stolen memory.
Apr 24 20:07:27 QUARTZ kernel: [ 37.162457] agpgart: AGP aperture is 128M @ 0xf0000000
Apr 24 20:07:27 QUARTZ kernel: [ 37.306097] intel_rng: FWH not detected
Apr 24 20:07:27 QUARTZ kernel: [ 37.928800] ACPI: AC Adapter [AC] (off-line)
Apr 24 20:07:27 QUARTZ kernel: [ 38.076755] input: PS/2 Mouse as /devices/virtual/input/input3
Apr 24 20:07:27 QUARTZ kernel: [ 38.103999] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input4
Apr 24 20:07:27 QUARTZ kernel: [ 38.242472] ACPI: Battery Slot [BAT0] (battery present)
Apr 24 20:07:27 QUARTZ kernel: [ 38.242664] input: Lid Switch as /devices/virtual/input/input5
Apr 24 20:07:27 QUARTZ kernel: [ 38.243168] ACPI: Lid Switch [LID]
Apr 24 20:07:27 QUARTZ kernel: [ 38.243249] input: Power Button (CM) as /devices/virtual/input/input6
Apr 24 20:07:27 QUARTZ kernel: [ 38.253995] ACPI: Power Button (CM) [PBTN]
Apr 24 20:07:27 QUARTZ kernel: [ 38.254088] input: Sleep Button (CM) as /devices/virtual/input/input7
Apr 24 20:07:27 QUARTZ kernel: [ 38.266020] ACPI: Sleep Button (CM) [SBTN]
Apr 24 20:07:27 QUARTZ kernel: [ 38.542584] ACPI: Battery Slot [BAT1] (battery present)
Apr 24 20:07:27 QUARTZ kernel: [ 38.883888] Yenta: CardBus bridge found at 0000:01:01.0 [1028:0163]
Apr 24 20:07:27 QUARTZ kernel: [ 38.883909] Yenta: Using CSCINT to route CSC interrupts to PCI
Apr 24 20:07:27 QUARTZ kernel: [ 38.883912] Yenta: Routing CardBus interrupts to PCI
Apr 24 20:07:27 QUARTZ kernel: [ 38.883918] Yenta TI: socket 0000:01:01.0, mfunc 0x012c1222, devctl 0x64
Apr 24 20:07:27 QUARTZ kernel: [ 38.945969] ieee80211_crypt: registered algorithm 'NULL'
Apr 24 20:07:27 QUARTZ kernel: [ 39.010153] ieee80211: 802.11 data/management/control stack, git-1.1.13
Apr 24 20:07:27 QUARTZ kernel: [ 39.010159] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
Apr 24 20:07:27 QUARTZ kernel: [ 39.114584] Yenta: ISA IRQ mask 0x04d8, PCI irq 11
Apr 24 20:07:27 QUARTZ kernel: [ 39.114590] Socket status: 30000086
Apr 24 20:07:27 QUARTZ kernel: [ 39.114594] Yenta: Raising subordinate bus# of parent bus (#01) from #01 to #05
Apr 24 20:07:27 QUARTZ kernel: [ 39.114602] pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff
Apr 24 20:07:27 QUARTZ kernel: [ 39.114607] cs: IO port probe 0xe000-0xefff: clean.
Apr 24 20:07:27 QUARTZ kernel: [ 39.115151] pcmcia: parent PCI bridge Memory window: 0xfc000000 - 0xfdffffff
Apr 24 20:07:27 QUARTZ kernel: [ 39.157971] ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2
Apr 24 20:07:27 QUARTZ kernel: [ 39.157977] ipw2100: Copyright(c) 2003-2006 Intel Corporation
Apr 24 20:07:27 QUARTZ kernel: [ 39.338100] ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
Apr 24 20:07:27 QUARTZ kernel: [ 39.338492] ipw2100: Detected Intel PRO/Wireless 2100 Network Connection
Apr 24 20:07:27 QUARTZ kernel: [ 39.538377] parport_pc 00:0c: reported by Plug and Play ACPI
Apr 24 20:07:27 QUARTZ kernel: [ 39.538428] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
Apr 24 20:07:27 QUARTZ kernel: [ 39.626549] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
Apr 24 20:07:27 QUARTZ kernel: [ 39.877976] irda_init()
Apr 24 20:07:27 QUARTZ kernel: [ 39.878001] NET: Registered protocol family 23
Apr 24 20:07:27 QUARTZ kernel: [ 40.222962] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:00/input/input8
Apr 24 20:07:27 QUARTZ kernel: [ 40.241972] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
Apr 24 20:07:27 QUARTZ kernel: [ 40.242197] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:01/input/input9
Apr 24 20:07:27 QUARTZ kernel: [ 40.273897] ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
Apr 24 20:07:27 QUARTZ kernel: [ 41.784903] Bluetooth: Core ver 2.11
Apr 24 20:07:27 QUARTZ kernel: [ 41.789228] NET: Registered protocol family 31
Apr 24 20:07:27 QUARTZ kernel: [ 41.789233] Bluetooth: HCI device and connection manager initialized
Apr 24 20:07:27 QUARTZ kernel: [ 41.789239] Bluetooth: HCI socket layer initialized
Apr 24 20:07:27 QUARTZ kernel: [ 41.823143] Bluetooth: HCI USB driver ver 2.9
Apr 24 20:07:27 QUARTZ kernel: [ 41.825131] usbcore: registered new interface driver hci_usb
Apr 24 20:07:27 QUARTZ kernel: [ 43.762137] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
Apr 24 20:07:27 QUARTZ kernel: [ 43.762173] PCI: Setting latency timer of device 0000:00:1f.5 to 64
Apr 24 20:07:27 QUARTZ kernel: [ 43.922750] cs: IO port probe 0x100-0x3af: excluding 0x280-0x287
Apr 24 20:07:27 QUARTZ kernel: [ 43.923607] cs: IO port probe 0x3e0-0x4ff: clean.
Apr 24 20:07:27 QUARTZ kernel: [ 43.923985] cs: IO port probe 0x820-0x8ff: clean.
Apr 24 20:07:27 QUARTZ kernel: [ 43.924054] cs: IO port probe 0xc00-0xcf7: clean.
Apr 24 20:07:27 QUARTZ kernel: [ 43.924552] cs: IO port probe 0xa00-0xaff: clean.
Apr 24 20:07:27 QUARTZ kernel: [ 44.589416] intel8x0_measure_ac97_clock: measured 55397 usecs
Apr 24 20:07:27 QUARTZ kernel: [ 44.589422] intel8x0: clocking to 48000
Apr 24 20:07:27 QUARTZ kernel: [ 45.749477] lp0: using parport0 (interrupt-driven).
Apr 24 20:07:27 QUARTZ kernel: [ 45.883485] EXT3 FS on sda2, internal journal
Apr 24 20:07:27 QUARTZ kernel: [ 46.924712] ip_tables: (C) 2000-2006 Netfilter Core Team
Apr 24 20:07:27 QUARTZ kernel: [ 47.277252] pnp 00:0d: disabled
Apr 24 20:07:27 QUARTZ kernel: [ 47.304372] pnp 00:0d: activated
Apr 24 20:07:27 QUARTZ kernel: [ 47.353770] pnp 00:0d: disabled
Apr 24 20:07:27 QUARTZ kernel: [ 47.380870] pnp 00:0d: activated
Apr 24 20:07:27 QUARTZ kernel: [ 48.187780] ACPI: ACPI Dock Station Driver
Apr 24 20:07:27 QUARTZ kernel: [ 48.770149] ACPI: Invalid _PSS data: freq is zero
Apr 24 20:07:27 QUARTZ NetworkManager: <info> starting...
Apr 24 20:07:27 QUARTZ NetworkManager: <info> Found dial up configuration for ppp0 via Modem: ppp0
Apr 24 20:07:28 QUARTZ avahi-daemon[5085]: Found user 'avahi' (UID 109) and group 'avahi' (GID 120).
Apr 24 20:07:28 QUARTZ avahi-daemon[5085]: Successfully dropped root privileges.
Apr 24 20:07:28 QUARTZ avahi-daemon[5085]: avahi-daemon 0.6.22 starting up.
Apr 24 20:07:28 QUARTZ avahi-daemon[5085]: Successfully called chroot().
Apr 24 20:07:28 QUARTZ avahi-daemon[5085]: Successfully dropped remaining capabilities.
Apr 24 20:07:28 QUARTZ avahi-daemon[5085]: No service file found in /etc/avahi/services.
Apr 24 20:07:28 QUARTZ avahi-daemon[5085]: Network interface enumeration completed.
Apr 24 20:07:28 QUARTZ avahi-daemon[5085]: Registering HINFO record with values 'I686'/'LINUX'.
Apr 24 20:07:28 QUARTZ avahi-daemon[5085]: Server startup complete. Host name is QUARTZ.local. Local service cookie is 2259136762.
Apr 24 20:07:29 QUARTZ mysqld_safe[5177]: started
Apr 24 20:07:29 QUARTZ mysqld[5181]: 100424 20:07:29 InnoDB: Started; log sequence number 0 43655
Apr 24 20:07:29 QUARTZ mysqld[5181]: 100424 20:07:29 [Note] /usr/sbin/mysqld: ready for connections.
Apr 24 20:07:29 QUARTZ mysqld[5181]: Version: '5.0.51a-3ubuntu5.4' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu)
Apr 24 20:07:30 QUARTZ /etc/mysql/debian-start[5218]: Upgrading MySQL tables if necessary.
Apr 24 20:07:30 QUARTZ kernel: [ 51.734488] apm: BIOS not found.
Apr 24 20:07:30 QUARTZ /etc/mysql/debian-start[5223]: Looking for 'mysql' in: /usr/bin/mysql
Apr 24 20:07:30 QUARTZ /etc/mysql/debian-start[5223]: Looking for 'mysqlcheck' in: /usr/bin/mysqlcheck
Apr 24 20:07:30 QUARTZ /etc/mysql/debian-start[5223]: This installation of MySQL is already upgraded to 5.0.51a, use --force if you still need to run mysql_upgrade
Apr 24 20:07:30 QUARTZ /etc/mysql/debian-start[5259]: Checking for insecure root accounts.
Apr 24 20:07:30 QUARTZ /etc/mysql/debian-start[5263]: Checking for crashed MySQL tables.
Apr 24 20:07:30 QUARTZ kernel: [ 51.976909] ppdev: user-space parallel port driver
Apr 24 20:07:30 QUARTZ kernel: [ 52.293680] audit(1272136050.708:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5275 profile="/usr/sbin/cupsd" namespace="default"
Apr 24 20:07:30 QUARTZ irattach: tcgetattr: Input/output error
Apr 24 20:07:30 QUARTZ irattach: Stopping device /dev/ttyS1
Apr 24 20:07:30 QUARTZ irattach: ioctl(SIOCGIFFLAGS): No such device
Apr 24 20:07:30 QUARTZ irattach: exiting ...
Apr 24 20:07:32 QUARTZ dhcdbd: Started up.
Apr 24 20:07:33 QUARTZ NetworkManager: <info> Found radio killswitch /org/freedesktop/Hal/devices/dell_wlan_switch
Apr 24 20:07:33 QUARTZ NetworkManager: <info> eth0: Device is fully-supported using driver 'e100'.
Apr 24 20:07:33 QUARTZ NetworkManager: <info> nm_device_init(): waiting for device's worker thread to start
Apr 24 20:07:33 QUARTZ NetworkManager: <info> nm_device_init(): device's worker thread started, continuing.
Apr 24 20:07:33 QUARTZ NetworkManager: <info> Now managing wired Ethernet (802.3) device 'eth0'.
Apr 24 20:07:33 QUARTZ NetworkManager: <info> Deactivating device eth0.
Apr 24 20:07:33 QUARTZ hcid[5542]: Bluetooth HCI daemon
Apr 24 20:07:33 QUARTZ hcid[5542]: HCI dev 0 registered
Apr 24 20:07:33 QUARTZ NetworkManager: <info> eth1: Device is fully-supported using driver 'ipw2100'.
Apr 24 20:07:33 QUARTZ NetworkManager: <info> eth1: driver does not support SSID scans (scan_capa 0x00).
Apr 24 20:07:33 QUARTZ NetworkManager: <info> nm_device_init(): waiting for device's worker thread to start
Apr 24 20:07:33 QUARTZ NetworkManager: <info> nm_device_init(): device's worker thread started, continuing.
Apr 24 20:07:33 QUARTZ NetworkManager: <info> Now managing wireless (802.11) device 'eth1'.
Apr 24 20:07:33 QUARTZ NetworkManager: <info> Deactivating device eth1.
Apr 24 20:07:33 QUARTZ hcid[5542]: Starting SDP server
Apr 24 20:07:33 QUARTZ kernel: [ 55.431435] Bluetooth: L2CAP ver 2.9
Apr 24 20:07:33 QUARTZ kernel: [ 55.431442] Bluetooth: L2CAP socket layer initialized
Apr 24 20:07:33 QUARTZ hcid[5542]: Created local server at unix:abstract=/var/run/dbus-ssot9ywvDk,guid=25a629e21865c3e740dc10cd4bd34175
Apr 24 20:07:33 QUARTZ audio[5552]: Bluetooth Audio daemon
Apr 24 20:07:33 QUARTZ hcid[5542]: HCI dev 0 up
Apr 24 20:07:33 QUARTZ hcid[5542]: Device hci0 has been added
Apr 24 20:07:33 QUARTZ audio[5552]: Unix socket created: 5
Apr 24 20:07:33 QUARTZ audio[5552]: audio.conf: Key file does not have key 'Enable'
Apr 24 20:07:33 QUARTZ audio[5552]: audio.conf: Key file does not have key 'Disable'
Apr 24 20:07:33 QUARTZ input[5553]: Bluetooth Input daemon
Apr 24 20:07:33 QUARTZ input[5553]: Registered input manager path:/org/bluez/input
Apr 24 20:07:33 QUARTZ NetworkManager: <info> Will activate wired connection 'eth0' because it now has a link.
Apr 24 20:07:34 QUARTZ hcid[5542]: Starting security manager 0
Apr 24 20:07:34 QUARTZ kernel: [ 55.620350] Bluetooth: RFCOMM socket layer initialized
Apr 24 20:07:34 QUARTZ kernel: [ 55.620374] Bluetooth: RFCOMM TTY layer initialized
Apr 24 20:07:34 QUARTZ kernel: [ 55.620377] Bluetooth: RFCOMM ver 1.8
Apr 24 20:07:34 QUARTZ NetworkManager: <info> Error getting killswitch power: org.freedesktop.Hal.Device.KillSwitch.NotSupported - Access type not supported
Apr 24 20:07:34 QUARTZ NetworkManager: <info> Wireless now enabled by radio killswitch
Apr 24 20:07:34 QUARTZ hcid[5542]: Device hci0 has been activated
Apr 24 20:07:34 QUARTZ kernel: [ 55.818566] pnp 00:0d: disabled
Apr 24 20:07:34 QUARTZ kernel: [ 55.846216] pnp 00:0d: activated
Apr 24 20:07:34 QUARTZ audio[5552]: add_service_record: got record id 0x10000
Apr 24 20:07:34 QUARTZ audio[5552]: audio.conf: Key file does not have key 'Disable'
Apr 24 20:07:34 QUARTZ audio[5552]: audio.conf: Key file does not have group 'A2DP'
Apr 24 20:07:34 QUARTZ last message repeated 3 times
Apr 24 20:07:34 QUARTZ audio[5552]: SEP 0x806d348 registered: type:0 codec:0 seid:1
Apr 24 20:07:34 QUARTZ audio[5552]: add_service_record: got record id 0x10001
Apr 24 20:07:34 QUARTZ audio[5552]: add_service_record: got record id 0x10002
Apr 24 20:07:34 QUARTZ audio[5552]: add_service_record: got record id 0x10003
Apr 24 20:07:34 QUARTZ audio[5552]: Registered manager path:/org/bluez/audio
Apr 24 20:07:34 QUARTZ kernel: [ 55.901143] pnp 00:0d: disabled
Apr 24 20:07:34 QUARTZ kernel: [ 55.929029] pnp 00:0d: activated
Apr 24 20:07:34 QUARTZ /usr/sbin/cron[5715]: (CRON) INFO (pidfile fd = 3)
Apr 24 20:07:34 QUARTZ /usr/sbin/cron[5719]: (CRON) STARTUP (fork ok)
Apr 24 20:07:34 QUARTZ /usr/sbin/cron[5719]: (CRON) INFO (Running @reboot jobs)
Apr 24 20:07:35 QUARTZ kernel: [ 57.243498] NET: Registered protocol family 10
Apr 24 20:07:35 QUARTZ kernel: [ 57.244157] lo: Disabled Privacy Extensions
Apr 24 20:07:35 QUARTZ kernel: [ 57.245034] ADDRCONF(NETDEV_UP): eth0: link is not ready
Apr 24 20:07:35 QUARTZ kernel: [ 57.245585] ADDRCONF(NETDEV_UP): eth1: link is not ready
Apr 24 20:07:36 QUARTZ kernel: [ 58.168764] ieee1394: raw1394: /dev/raw1394 device initialized
Apr 24 20:07:36 QUARTZ kernel: [ 58.212058] [drm] Initialized drm 1.1.0 20060810
Apr 24 20:07:36 QUARTZ kernel: [ 58.245426] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Apr 24 20:07:36 QUARTZ kernel: [ 58.245439] PCI: Setting latency timer of device 0000:00:02.0 to 64
Apr 24 20:07:36 QUARTZ kernel: [ 58.245546] [drm] Initialized i915 1.6.0 20060119 on minor 0
Apr 24 20:07:36 QUARTZ kernel: [ 58.245560] PCI: Setting latency timer of device 0000:00:02.1 to 64
Apr 24 20:07:36 QUARTZ kernel: [ 58.245632] [drm] Initialized i915 1.6.0 20060119 on minor 1
Apr 24 20:07:36 QUARTZ NetworkManager: <debug> [1272136056.683334] nm_hal_device_added(): New device added (hal udi is '/org/freedesktop/Hal/devices/pci_8086_3582_drm_i915_card0').
Apr 24 20:07:36 QUARTZ NetworkManager: <debug> [1272136056.689746] nm_hal_device_added(): New device added (hal udi is '/org/freedesktop/Hal/devices/pci_8086_3582_0_drm_i915_card1').
Apr 24 20:08:20 QUARTZ hcid[5542]: Default passkey agent (:1.17, /org/bluez/passkey) registered
Apr 24 20:08:20 QUARTZ hcid[5542]: Default authorization agent (:1.17, /org/bluez/auth) registered
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Updating allowed wireless network lists.
Apr 24 20:08:24 QUARTZ NetworkManager: <info> SWITCH: no current connection, found better connection 'eth1'.
Apr 24 20:08:24 QUARTZ dhcdbd: message_handler: message handler not found under /com/redhat/dhcp/eth1 for sub-path eth1.dbus.get.reason
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Will activate connection 'eth1/chocolate'.
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Device eth1 activation scheduled...
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Activation (eth1) started...
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled...
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started...
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled...
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete.
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting...
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Activation (eth1/wireless): access point 'chocolate' is unencrypted, no key needed.
Apr 24 20:08:24 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:08:24 QUARTZ last message repeated 2 times
Apr 24 20:08:26 QUARTZ NetworkManager: <info> retry to connect to global supplicant socket (try=1)
Apr 24 20:08:26 QUARTZ NetworkManager: <info> SUP: sending command 'INTERFACE_ADD eth1^I^Iwext^I/var/run/wpa_supplicant0^I'
Apr 24 20:08:26 QUARTZ kernel: [ 108.329756] NET: Registered protocol family 17
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> kernel_driver for non broadcast check: ipw2100 (has_scan_capa_ssid=0)
Apr 24 20:08:27 QUARTZ NetworkManager: <info> Using plain AP_SCAN 2 for ipw2100
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: sending command 'AP_SCAN 2'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: sending command 'ADD_NETWORK'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: response was '0'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 ssid 63686f636f6c617465'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 scan_ssid 1'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 key_mgmt NONE'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: sending command 'ENABLE_NETWORK 0'
Apr 24 20:08:27 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:08:27 QUARTZ kernel: [ 108.915109] ipw2100: Fatal interrupt. Scheduling firmware restart.
Apr 24 20:08:27 QUARTZ kernel: [ 108.943630] ipw2100: Fatal interrupt. Scheduling firmware restart.
Apr 24 20:08:29 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete.
Apr 24 20:08:29 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:08:54 QUARTZ last message repeated 4 times
Apr 24 20:09:01 QUARTZ /USR/SBIN/CRON[6301]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -type f -cmin +$(/usr/lib/php5/maxlifetime) -print0 | xargs -r -0 rm)
Apr 24 20:09:02 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:09:07 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:09:12 QUARTZ dhcdbd: message_handler: message handler not found under /com/redhat/dhcp/eth1 for sub-path eth1.dbus.get.reason
Apr 24 20:09:12 QUARTZ NetworkManager: <debug> [1272136152.856397] nm_device_802_11_wireless_get_activation_ap(): Forcing AP 'chocolate'
Apr 24 20:09:12 QUARTZ NetworkManager: <info> User Switch: /org/freedesktop/NetworkManager/Devices/eth1 / chocolate
Apr 24 20:09:12 QUARTZ NetworkManager: <info> Deactivating device eth1.
Apr 24 20:09:12 QUARTZ NetworkManager: <info> Activation (eth1): cancelling...
Apr 24 20:09:12 QUARTZ NetworkManager: <info> Activation (eth1) cancellation handler scheduled...
Apr 24 20:09:12 QUARTZ NetworkManager: <info> Activation (eth1): waiting for device to cancel activation.
Apr 24 20:09:12 QUARTZ NetworkManager: <info> Activation (eth1) cancellation handled.
Apr 24 20:09:12 QUARTZ NetworkManager: <info> Activation (eth1): cancelled.
Apr 24 20:09:13 QUARTZ NetworkManager: <info> Device eth1 activation scheduled...
Apr 24 20:09:13 QUARTZ NetworkManager: <info> Activation (eth1) started...
Apr 24 20:09:13 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled...
Apr 24 20:09:13 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started...
Apr 24 20:09:13 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled...
Apr 24 20:09:13 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete.
Apr 24 20:09:13 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting...
Apr 24 20:09:13 QUARTZ NetworkManager: <info> Activation (eth1/wireless): access point 'chocolate' is unencrypted, no key needed.
Apr 24 20:09:14 QUARTZ NetworkManager: <info> SUP: sending command 'INTERFACE_ADD eth1^I^Iwext^I/var/run/wpa_supplicant0^I'
Apr 24 20:09:14 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:14 QUARTZ kernel: [ 156.373114] ipw2100: Fatal interrupt. Scheduling firmware restart.
Apr 24 20:09:15 QUARTZ NetworkManager: <info> kernel_driver for non broadcast check: ipw2100 (has_scan_capa_ssid=0)
Apr 24 20:09:15 QUARTZ NetworkManager: <info> Using plain AP_SCAN 2 for ipw2100
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: sending command 'AP_SCAN 2'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: sending command 'ADD_NETWORK'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: response was '0'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 ssid 63686f636f6c617465'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 scan_ssid 1'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 key_mgmt NONE'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: sending command 'ENABLE_NETWORK 0'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:15 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete.
Apr 24 20:09:17 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:09:22 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:09:24 QUARTZ dhcdbd: message_handler: message handler not found under /com/redhat/dhcp/eth1 for sub-path eth1.dbus.get.reason
Apr 24 20:09:24 QUARTZ NetworkManager: <debug> [1272136164.710360] nm_device_802_11_wireless_get_activation_ap(): Forcing AP 'chocolate'
Apr 24 20:09:24 QUARTZ NetworkManager: <info> User Switch: /org/freedesktop/NetworkManager/Devices/eth1 / chocolate
Apr 24 20:09:24 QUARTZ NetworkManager: <info> Deactivating device eth1.
Apr 24 20:09:24 QUARTZ NetworkManager: <info> Activation (eth1): cancelling...
Apr 24 20:09:24 QUARTZ NetworkManager: <info> Activation (eth1) cancellation handler scheduled...
Apr 24 20:09:24 QUARTZ NetworkManager: <info> Activation (eth1): waiting for device to cancel activation.
Apr 24 20:09:24 QUARTZ NetworkManager: <info> Activation (eth1) cancellation handled.
Apr 24 20:09:24 QUARTZ NetworkManager: <info> Activation (eth1): cancelled.
Apr 24 20:09:25 QUARTZ NetworkManager: <info> Device eth1 activation scheduled...
Apr 24 20:09:25 QUARTZ NetworkManager: <info> Activation (eth1) started...
Apr 24 20:09:25 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled...
Apr 24 20:09:25 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started...
Apr 24 20:09:25 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled...
Apr 24 20:09:25 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete.
Apr 24 20:09:25 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting...
Apr 24 20:09:25 QUARTZ NetworkManager: <info> Activation (eth1/wireless): access point 'chocolate' is unencrypted, no key needed.
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: sending command 'INTERFACE_ADD eth1^I^Iwext^I/var/run/wpa_supplicant0^I'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> kernel_driver for non broadcast check: ipw2100 (has_scan_capa_ssid=0)
Apr 24 20:09:26 QUARTZ NetworkManager: <info> Using plain AP_SCAN 2 for ipw2100
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: sending command 'AP_SCAN 2'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: sending command 'ADD_NETWORK'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: response was '0'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 ssid 63686f636f6c617465'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 scan_ssid 1'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 key_mgmt NONE'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: sending command 'ENABLE_NETWORK 0'
Apr 24 20:09:26 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:09:26 QUARTZ kernel: [ 168.546443] ipw2100: Fatal interrupt. Scheduling firmware restart.
Apr 24 20:09:26 QUARTZ kernel: [ 168.568555] ipw2100: Fatal interrupt. Scheduling firmware restart.
Apr 24 20:09:29 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete.
Apr 24 20:09:33 QUARTZ kernel: [ 174.879512] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Apr 24 20:09:33 QUARTZ NetworkManager: <info> Supplicant state changed: 1
Apr 24 20:09:33 QUARTZ NetworkManager: <info> Activation (eth1/wireless) Stage 2 of 5 (Device Configure) successful. Connected to access point 'chocolate'.
Apr 24 20:09:33 QUARTZ NetworkManager: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) scheduled.
Apr 24 20:09:33 QUARTZ NetworkManager: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) started...
Apr 24 20:09:34 QUARTZ NetworkManager: <info> Activation (eth1) Beginning DHCP transaction.
Apr 24 20:09:34 QUARTZ NetworkManager: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) complete.
Apr 24 20:09:34 QUARTZ NetworkManager: <info> DHCP daemon state is now 12 (successfully started) for interface eth1
Apr 24 20:09:34 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:09:34 QUARTZ avahi-daemon[5085]: Registering new address record for fe80::20c:f1ff:fe31:14aa on eth1.*.
Apr 24 20:09:35 QUARTZ NetworkManager: <info> DHCP daemon state is now 1 (starting) for interface eth1
Apr 24 20:09:37 QUARTZ dhclient: DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 8
Apr 24 20:09:39 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:09:43 QUARTZ kernel: [ 185.348557] eth1: no IPv6 routers present
Apr 24 20:09:45 QUARTZ dhclient: DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 12
Apr 24 20:09:57 QUARTZ dhclient: DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 11
Apr 24 20:10:01 QUARTZ /USR/SBIN/CRON[6441]: (www-data) CMD ([ -f /usr/share/moodle/admin/cron.php ] && /usr/bin/php -f /usr/share/moodle/admin/cron.php > /dev/null)
Apr 24 20:10:06 QUARTZ dhclient: DHCPOFFER of 192.168.0.4 from 192.168.0.1
Apr 24 20:10:06 QUARTZ dhclient: DHCPREQUEST of 192.168.0.4 on eth1 to 255.255.255.255 port 67
Apr 24 20:10:14 QUARTZ dhclient: DHCPREQUEST of 192.168.0.4 on eth1 to 255.255.255.255 port 67
Apr 24 20:10:35 QUARTZ dhclient: DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 7
Apr 24 20:10:42 QUARTZ dhclient: DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 13
Apr 24 20:10:55 QUARTZ dhclient: DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 11
Apr 24 20:10:58 QUARTZ NetworkManager: <debug> [1272136258.369100] nm_device_802_11_wireless_get_activation_ap(): Forcing AP 'chocolate'
Apr 24 20:10:58 QUARTZ NetworkManager: <info> User Switch: /org/freedesktop/NetworkManager/Devices/eth1 / chocolate
Apr 24 20:10:58 QUARTZ NetworkManager: <info> Deactivating device eth1.
Apr 24 20:10:58 QUARTZ NetworkManager: <info> Activation (eth1): cancelling...
Apr 24 20:10:58 QUARTZ NetworkManager: <info> Activation (eth1) cancellation handler scheduled...
Apr 24 20:10:58 QUARTZ NetworkManager: <info> Activation (eth1): waiting for device to cancel activation.
Apr 24 20:10:58 QUARTZ dhclient: There is already a pid file /var/run/dhclient.eth1.pid with pid 6410
Apr 24 20:10:58 QUARTZ dhclient: killed old client process, removed PID file
Apr 24 20:10:58 QUARTZ dhclient: DHCPRELEASE on eth1 to 192.168.0.1 port 67
Apr 24 20:10:58 QUARTZ dhclient: send_packet: Network is unreachable
Apr 24 20:10:58 QUARTZ dhclient: send_packet: please consult README file regarding broadcast address.
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Activation (eth1) cancellation handled.
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Activation (eth1): cancelled.
Apr 24 20:10:59 QUARTZ NetworkManager: nm_utils_supplicant_request_with_check: assertion `ctrl != NULL' failed
Apr 24 20:10:59 QUARTZ NetworkManager: <WARN> nm_device_802_11_wireless_scan(): (eth1): could not trigger wireless scan
Apr 24 20:10:59 QUARTZ avahi-daemon[5085]: Withdrawing address record for fe80::20c:f1ff:fe31:14aa on eth1.
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Device eth1 activation scheduled...
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Activation (eth1) started...
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled...
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started...
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled...
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete.
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting...
Apr 24 20:10:59 QUARTZ NetworkManager: <info> Activation (eth1/wireless): access point 'chocolate' is unencrypted, no key needed.
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: sending command 'INTERFACE_ADD eth1^I^Iwext^I/var/run/wpa_supplicant0^I'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: sending command 'AP_SCAN 1'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: sending command 'ADD_NETWORK'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: response was '0'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 ssid 63686f636f6c617465'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: sending command 'SET_NETWORK 0 key_mgmt NONE'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: sending command 'ENABLE_NETWORK 0'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> SUP: response was 'OK'
Apr 24 20:11:01 QUARTZ NetworkManager: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete.
Apr 24 20:11:06 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:11:07 QUARTZ kernel: [ 269.112038] ipw2100: Fatal interrupt. Scheduling firmware restart.
Apr 24 20:11:15 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:11:17 QUARTZ kernel: [ 278.939962] ipw2100: Fatal interrupt. Scheduling firmware restart.
Apr 24 20:11:21 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:11:50 QUARTZ last message repeated 4 times
Apr 24 20:12:00 QUARTZ NetworkManager: <info> Old device 'eth1' activating, won't change.
Apr 24 20:12:01 QUARTZ NetworkManager: <info> Activation (eth1/wireless): association took too long (>60s), failing activation.
Apr 24 20:12:01 QUARTZ NetworkManager: <info> Activation (eth1) failure scheduled...
Apr 24 20:12:01 QUARTZ NetworkManager: <info> Activation (eth1) failed for access point (chocolate)
Apr 24 20:12:01 QUARTZ NetworkManager: <info> Activation (eth1) failed.
Apr 24 20:12:01 QUARTZ NetworkManager: <info> Deactivating device eth1.
Apr 24 20:12:05 QUARTZ kernel: [ 327.420808] ipw2100: Fatal interrupt. Scheduling firmware restart.
Apr 24 20:12:54 QUARTZ kernel: [ 376.514894] Not cloning cgroup for unused subsystem ns
Apr 24 20:12:55 QUARTZ init: tty4 main process (4641) killed by TERM signal
Apr 24 20:12:55 QUARTZ init: tty5 main process (4642) killed by TERM signal
Apr 24 20:12:55 QUARTZ init: tty2 main process (4646) killed by TERM signal
Apr 24 20:12:55 QUARTZ init: tty3 main process (4647) killed by TERM signal
Apr 24 20:12:55 QUARTZ init: tty6 main process (4648) killed by TERM signal
Apr 24 20:12:55 QUARTZ init: tty1 main process (5902) killed by TERM signal
Apr 24 20:12:56 QUARTZ gdm[5622]: GLib-CRITICAL: g_hash_table_lookup_extended: assertion `hash_table != NULL' failed
Apr 24 20:12:56 QUARTZ gdm[5622]: WARNING: Request for invalid configuration key xdmcp/Enable=false
Apr 24 20:12:56 QUARTZ avahi-daemon[5085]: Got SIGTERM, quitting.
Apr 24 20:12:56 QUARTZ mysqld[5181]: 100424 20:12:56 [Note] /usr/sbin/mysqld: Normal shutdown
Apr 24 20:12:56 QUARTZ mysqld[5181]:
Apr 24 20:12:56 QUARTZ mysqld[5181]: 100424 20:12:56 InnoDB: Starting shutdown...
Apr 24 20:12:57 QUARTZ mysqld[5181]: 100424 20:12:57 InnoDB: Shutdown completed; log sequence number 0 43655
Apr 24 20:12:57 QUARTZ mysqld[5181]: 100424 20:12:57 [Note] /usr/sbin/mysqld: Shutdown complete
Apr 24 20:12:57 QUARTZ mysqld[5181]:
Apr 24 20:12:57 QUARTZ mysqld_safe[6828]: ended
Apr 24 20:13:00 QUARTZ exiting on signal 15
Thanks for help so far