Hi SandMan! Welcome!
For the problem with your resolution try to boot with the liveCD then go to your hard disk to modify your /etc/X11/xorg.conf file with your resolution and change the driver section with 'nv'.
Also you should be able to modify the lines HorizSync and VertRefresh with the specifications of your monitor. Then reboot from your hard disk.
With this you will use the generic driver but at least you should be able to use Mint.
Hope that solve this problem.
I am such a Newbie...
Forum rules
There are no such things as "stupid" questions. However if you think your question is a bit stupid, then this is the right place for you to post it. Stick to easy to-the-point questions that you feel people can answer fast. For long and complicated questions use the other forums in the support section.
Before you post read how to get help. Topics in this forum are automatically closed 6 months after creation.
There are no such things as "stupid" questions. However if you think your question is a bit stupid, then this is the right place for you to post it. Stick to easy to-the-point questions that you feel people can answer fast. For long and complicated questions use the other forums in the support section.
Before you post read how to get help. Topics in this forum are automatically closed 6 months after creation.
- linuxviolin
- Level 8
- Posts: 2081
- Joined: Tue Feb 27, 2007 6:55 pm
- Location: France
Last edited by LockBot on Wed Dec 28, 2022 7:16 am, edited 1 time in total.
Reason: Topic automatically closed 6 months after creation. New replies are no longer allowed.
Reason: Topic automatically closed 6 months after creation. New replies are no longer allowed.
K.I.S.S. ===> "Keep It Simple, Stupid"
"Simplicity is the ultimate sophistication." (Leonardo da Vinci)
"Everything should be made as simple as possible, but no simpler." (Albert Einstein)
"Simplicity is the ultimate sophistication." (Leonardo da Vinci)
"Everything should be made as simple as possible, but no simpler." (Albert Einstein)
Even if the GUI (desktop) doesn't boot you can boot into recovery mode and edit the xorg.conf file with nano.
Anyway... once you're reloaded and booted into the Mint desktop, try it again, but before you do anything at all execute the following command (from a terminal):
If you have problems booting after installing the ATI driver, boot into recovery mode from the grub boot menu; log in to the command shell, and enter the command:
which will restore the default file and let you reboot into GNOME.
Now, when you are installing the ATI driver and editing your xorg.conf file, also look for this section:
and add a Modes line, like this:
And, if you know the spec's on your monitor, you can add them as well. Look for the section that identifies your monitor and add these lines below the Option "DPMS" entry:
Once you are done installing fglrx and editing xorg.conf, save your changes, but before you reboot do this:
Which will make a copy of your edited xorg file. Then if you need further help you can post that here for us to take a look at. Hopefully the changes above will get you going though. I also recently posted a message about using Synaptic to install the fglrx driver, which can be found here (my 2nd post in the thread):
http://linuxmint.com/forum/viewtopic.php?t=6262
If you're more comfortable using Synaptic you could give that a try.
And finally; you can also edit the xorg.conf file from recovery mode with the nano text editor. From the recovery command shell, enter:
This is a non-graphical editor. All cursor controls and keyboard (no mouse). The easiest fix for a non-booting system is to simply change Driver "fglrx" to Driver "vesa" then hit CONTROL+X then Y Enter to save the file.
Good luck!
Aloha, Tim
Anyway... once you're reloaded and booted into the Mint desktop, try it again, but before you do anything at all execute the following command (from a terminal):
Code: Select all
sudo cp /etc/X11/xorg.conf /etc/X11/xorg.conf.backup
Code: Select all
sudo cp /etc/X11/xorg.conf.backup /etc/X11/xorg.conf
Now, when you are installing the ATI driver and editing your xorg.conf file, also look for this section:
Code: Select all
SubSection "Display"
Depth 24
EndSubSection
Code: Select all
SubSection "Display"
Depth 24
Modes "1280x1024"
EndSubSection
Code: Select all
Option "DPMS"
HorizSync 28-80 # substitute YOUR monitor's spec's here !!
VertRefresh 48-75 # and here...
Code: Select all
sudo cp /etc/X11/xorg.conf /etc/X11/xorg.conf.ati
http://linuxmint.com/forum/viewtopic.php?t=6262
If you're more comfortable using Synaptic you could give that a try.
And finally; you can also edit the xorg.conf file from recovery mode with the nano text editor. From the recovery command shell, enter:
Code: Select all
sudo nano /etc/X11/xorg.conf
Good luck!
Aloha, Tim