Linux Mint Forums

Skip to content

Copy to USB devices slow and problematic

Questions about hardware,drivers and peripherals
Forum rules
Before you post please read this
Post a reply

Copy to USB devices slow and problematic

Postby J@n on Sat Jan 28, 2012 8:48 am

Hi All,

I have a problem with my USB mass storage devices which I can't find a solution for on the forum(s). I will try to be as detailled as possible.

Problem description:
If I try to copy files to a USB storage device it just seems to stop copying (the progress indicator of Nautilus just stops and sits and waits forever). This happens with all USB sticks (thumbdrives) and on all USB ports (USB 2.0 and USB 3.0)

Actions taken:
Searched this forum and "ẗhe other one" (ubuntu) but did not find a solution
Changed grub settings to "pci=acpi" but no luck
Tried copying from the terminal. It did copy but after the first or second file it became as slow as molases.
Tried to copy from my virtualized Windows 7 (64 bit). Copying did not stop but the speed slowed down to an unbearable 2.5 MB/sec
Booted the Mint 12 Live CD but that showed the same problems
Booted Ubuntu 11.10 Live CD but that did not even booted properly
Tried to fill the drive from a network share with FileZilla. It stopped (or became extremely slow) after a file or two.

I am out of ideas of how to solve this.

Some system specs:
Mint 12 64 bit
MB: ASRock 880GMH/U3S3
Phenom II X4 965
16 GB DDR3 Memory
System drve is an SSD
There ar two internal HDD's connected to a SATA II interface

Any help truly appreciated!

Greetz,

J@n
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top
Linux Mint is funded by ads and donations.
 
Top

Re: Copy to USB devices slow and problematic

Postby doktornotor on Sat Jan 28, 2012 9:21 am

What is the output of the following?

Code: Select all
sudo lsusb -v
doktornotor
Level 4
Level 4
 
Posts: 211
Joined: Mon Jan 23, 2012 6:28 pm
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Sat Jan 28, 2012 10:31 am

Hi doktornotor,

Thank you for your interest in my issue. I executed the command you posted and it resulted in quite a lot of information (40 KB to be precise:))

So here it is:
Code: Select all
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic ehci_hcd
  iProduct                2 EHCI Host Controller
  iSerial                 1 0000:00:12.2
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             6
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0503 highspeed power enable connect
   Port 4: 0000.0507 highspeed power suspend enable connect
   Port 5: 0000.0100 power
   Port 6: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic ehci_hcd
  iProduct                2 EHCI Host Controller
  iSerial                 1 0000:00:13.2
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             6
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0503 highspeed power enable connect
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
   Port 4: 0000.0100 power
   Port 5: 0000.0100 power
   Port 6: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic ohci_hcd
  iProduct                2 OHCI Host Controller
  iSerial                 1 0000:00:12.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             3
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic ohci_hcd
  iProduct                2 OHCI Host Controller
  iSerial                 1 0000:00:12.1
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             3
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic ohci_hcd
  iProduct                2 OHCI Host Controller
  iSerial                 1 0000:00:13.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             3
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic ohci_hcd
  iProduct                2 OHCI Host Controller
  iSerial                 1 0000:00:13.1
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             3
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic ohci_hcd
  iProduct                2 OHCI Host Controller
  iSerial                 1 0000:00:14.5
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic xhci_hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 0000:02:00.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
    TT think time 8 FS bits
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         3
  bMaxPacketSize0         9
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0003 3.0 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic xhci_hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 0000:02:00.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           31
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
        bMaxBurst               0
Hub Descriptor:
  bLength              12
  bDescriptorType      42
  nNbrPorts             2
  wHubCharacteristic 0x0009
    Per-port power switching
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  bHubDecLat          0.0 micro seconds
  wHubDelay             0 nano seconds
  DeviceRemovable    0x00
 Hub Port Status:
   Port 1: 0000.02a0 5Gbps power Rx.Detect
   Port 2: 0000.02a0 5Gbps power Rx.Detect
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 010 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic xhci_hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 0000:03:00.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
    TT think time 8 FS bits
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0503 highspeed power enable connect
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 011 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         3
  bMaxPacketSize0         9
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0003 3.0 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-13-generic xhci_hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 0000:03:00.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           31
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
        bMaxBurst               0
Hub Descriptor:
  bLength              12
  bDescriptorType      42
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  bHubDecLat          0.0 micro seconds
  wHubDelay             0 nano seconds
  DeviceRemovable    0x00
 Hub Port Status:
   Port 1: 0000.02a0 5Gbps power Rx.Detect
   Port 2: 0000.02a0 5Gbps power Rx.Detect
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x05e3 Genesys Logic, Inc.
  idProduct          0x0608 USB-2.0 4-Port HUB
  bcdDevice           77.64
  iManufacturer           0
  iProduct                1 USB2.0 Hub
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             4
  wHubCharacteristic 0x00e0
    Ganged power switching
    Ganged overcurrent protection
    TT think time 32 FS bits
    Port indicators
  bPwrOn2PwrGood       50 * 2 milli seconds
  bHubContrCurrent    100 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0303 lowspeed power enable connect
   Port 4: 0000.0303 lowspeed power enable connect
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered

Bus 001 Device 003: ID 1a40:0101 TERMINUS TECHNOLOGY INC. USB-2.0 4-Port HUB
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x1a40 TERMINUS TECHNOLOGY INC.
  idProduct          0x0101 USB-2.0 4-Port HUB
  bcdDevice            1.11
  iManufacturer           0
  iProduct                1 USB 2.0 Hub
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             4
  wHubCharacteristic 0x0000
    Ganged power switching
    Ganged overcurrent protection
    TT think time 8 FS bits
  bPwrOn2PwrGood       50 * 2 milli seconds
  bHubContrCurrent    100 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0507 highspeed power suspend enable connect
   Port 3: 0000.0100 power
   Port 4: 0000.0100 power
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered

Bus 002 Device 002: ID 058f:6377 Alcor Micro Corp. Multimedia Card Reader
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x058f Alcor Micro Corp.
  idProduct          0x6377 Multimedia Card Reader
  bcdDevice            1.00
  iManufacturer           1 Generic
  iProduct                2 Mass Storage Device
  iSerial                 3 920321111113
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)

Bus 001 Device 004: ID 046d:c05a Logitech, Inc. Optical Mouse M90
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x046d Logitech, Inc.
  idProduct          0xc05a Optical Mouse M90
  bcdDevice           63.00
  iManufacturer           1 Logitech
  iProduct                2 USB Optical Mouse
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           34
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      2 Mouse
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.11
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      52
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              10
Device Status:     0x0000
  (Bus Powered)

Bus 001 Device 005: ID 04d9:1603 Holtek Semiconductor, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x04d9 Holtek Semiconductor, Inc.
  idProduct          0x1603
  bcdDevice            3.10
  iManufacturer           1 
  iProduct                2 USB Keyboard
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           59
    bNumInterfaces          2
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      1 Keyboard
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      62
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength     101
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10
Device Status:     0x0000
  (Bus Powered)

Bus 001 Device 006: ID 1a40:0101 TERMINUS TECHNOLOGY INC. USB-2.0 4-Port HUB
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x1a40 TERMINUS TECHNOLOGY INC.
  idProduct          0x0101 USB-2.0 4-Port HUB
  bcdDevice            1.11
  iManufacturer           0
  iProduct                1 USB 2.0 Hub
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             4
  wHubCharacteristic 0x0000
    Ganged power switching
    Ganged overcurrent protection
    TT think time 8 FS bits
  bPwrOn2PwrGood       50 * 2 milli seconds
  bHubContrCurrent    100 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0100 power
   Port 4: 0000.0100 power
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered

Bus 010 Device 002: ID 0951:1653 Kingston Technology
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0951 Kingston Technology
  idProduct          0x1653
  bcdDevice            1.00
  iManufacturer           1 Kingston
  iProduct                2 DT 100 G2
  iSerial                 3 001478544884BBB137BB0960
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              200mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)


I hope you can find anything indicating the problem.

Thanks again!

Greetz,

J@n
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top

Re: Copy to USB devices slow and problematic

Postby wgking on Thu Feb 02, 2012 2:05 am

I am having the same issue. There is a long pause (~40-90 sec) at the end of each file copied.

I am running Isadora / Lucid Lynx 64 bit with current updates on a quad core 8GB system.

Copies eventually finish OK - its just annoying.

Any ideas would be appreciated.
wgking
Level 1
Level 1
 
Posts: 1
Joined: Thu Feb 02, 2012 1:48 am
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Fri Feb 03, 2012 11:56 am

Hi wgking,

Nice to know I am not the only one :?

But it seems we are the only two in the world to be troubled by this. Or is the description of the problem not clear?

Come on, Guruus! Please help us humble noobs..

Greetz,

J@n
Last edited by J@n on Sun Feb 05, 2012 6:26 am, edited 1 time in total.
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top

Re: Copy to USB devices slow and problematic

Postby Core Dumped on Sat Feb 04, 2012 3:10 pm

Hey,

you're not alone! The same here: a lot of wasting time during any file copy.

Fresh Linux Mint 12 Lisa installation, IBM IntelliStation and USB-2 devices.
More than one hour to copy 1.2GB from the local HDD to the USB stick.

Here's the lsusb -v output:
Code: Select all
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-12-generic ehci_hcd
  iProduct                2 EHCI Host Controller
  iSerial                 1 0000:00:1d.7
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             4
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
   Port 3: 0000.0503 highspeed power enable connect
   Port 4: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-12-generic uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0303 lowspeed power enable connect
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.00
  iManufacturer           3 Linux 3.0.0-12-generic uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:1d.1
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 001 Device 003: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0bda Realtek Semiconductor Corp.
  idProduct          0x8187 RTL8187 Wireless Adapter
  bcdDevice            1.00
  iManufacturer           1 Manufacturer_Realtek_RTL8187_
  iProduct                2 RTL8187_Wireless
  iSerial                 3 00C0CA47807A
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           39
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          4 Wireless Network Card
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass         0 (Defined at Interface level)
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              5 Bulk-IN,Bulk-OUT,Bulk-OUT
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)

Bus 002 Device 002: ID 045e:0025 Microsoft Corp. IntelliEye Mouse
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x045e Microsoft Corp.
  idProduct          0x0025 IntelliEye Mouse
  bcdDevice            1.00
  iManufacturer           1 Microsoft
  iProduct                2 Microsoft IntelliMouse � with IntelliEye
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           34
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      2 Mouse
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.00
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      52
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              10
Device Status:     0x0000
  (Bus Powered)



Before with Fedora 15 I had no issues with USB speed, all devices were recognized correctly and on-fly,
included the printer's USB-multireader card. Now it is a pain.

CD
Core Dumped
Level 1
Level 1
 
Posts: 3
Joined: Fri Dec 09, 2011 2:31 am
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Sun Feb 05, 2012 6:18 am

Hi Core Dumped,

Welcome to the club :wink:

Maybe I will try a completely different distro (Suse i.e.) with a live CD to see if that will do the trick.

But in the meantime I have some information to add to my first post. Who knows....maybe some Guru will stumble by and can use the information :)

Output of lsusb:
Code: Select all
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 010 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 011 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 001 Device 003: ID 1a40:0101 TERMINUS TECHNOLOGY INC. USB-2.0 4-Port HUB
Bus 002 Device 002: ID 058f:6377 Alcor Micro Corp. Multimedia Card Reader
Bus 001 Device 004: ID 046d:c05a Logitech, Inc. Optical Mouse M90
Bus 001 Device 005: ID 04d9:1603 Holtek Semiconductor, Inc.
Bus 001 Device 006: ID 1a40:0101 TERMINUS TECHNOLOGY INC. USB-2.0 4-Port HUB


Output of dmesg|grep usb:
Code: Select all
[    0.394758] usbcore: registered new interface driver usbfs
[    0.394758] usbcore: registered new interface driver hub
[    0.394758] usbcore: registered new device driver usb
[    1.864032] usb 1-3: new high speed USB device number 2 using ehci_hcd
[    2.112053] usb 1-4: new high speed USB device number 3 using ehci_hcd
[    2.356031] usb 2-1: new high speed USB device number 2 using ehci_hcd
[    2.492306] usbcore: registered new interface driver uas
[    2.523934] scsi8 : usb-storage 2-1:1.0
[    2.524331] usbcore: registered new interface driver usb-storage
[    2.560473] usb 1-3.3: new low speed USB device number 4 using ehci_hcd
[    2.732464] usb 1-3.4: new low speed USB device number 5 using ehci_hcd
[    2.916323] usb 1-4.2: new high speed USB device number 6 using ehci_hcd
[    7.983927] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:12.2/usb1/1-3/1-3.3/1-3.3:1.0/input/input2
[    7.984030] generic-usb 0003:046D:C05A.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:12.2-3.3/input0
[    7.994078] input:   USB Keyboard as /devices/pci0000:00/0000:00:12.2/usb1/1-3/1-3.4/1-3.4:1.0/input/input3
[    7.994804] generic-usb 0003:04D9:1603.0002: input,hidraw1: USB HID v1.10 Keyboard [  USB Keyboard] on usb-0000:00:12.2-3.4/input0
[    8.011813] input:   USB Keyboard as /devices/pci0000:00/0000:00:12.2/usb1/1-3/1-3.4/1-3.4:1.1/input/input4
[    8.011879] generic-usb 0003:04D9:1603.0003: input,hidraw2: USB HID v1.10 Device [  USB Keyboard] on usb-0000:00:12.2-3.4/input1
[    8.011893] usbcore: registered new interface driver usbhid
[    8.011894] usbhid: USB HID core driver


And the output from sudo lspci -v:
Code: Select all
*snip*
00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
   Subsystem: ASRock Incorporation Device 4397
   Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16
   Memory at ff70a000 (32-bit, non-prefetchable) [size=4K]
   Kernel driver in use: ohci_hcd

00:12.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller (prog-if 10 [OHCI])
   Subsystem: ASRock Incorporation Device 4398
   Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16
   Memory at ff709000 (32-bit, non-prefetchable) [size=4K]
   Kernel driver in use: ohci_hcd

00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
   Subsystem: ASRock Incorporation Device 4396
   Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17
   Memory at ff708000 (32-bit, non-prefetchable) [size=256]
   Capabilities: [c0] Power Management version 2
   Capabilities: [e4] Debug port: BAR=1 offset=00e0
   Kernel driver in use: ehci_hcd

00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
   Subsystem: ASRock Incorporation Device 4397
   Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18
   Memory at ff707000 (32-bit, non-prefetchable) [size=4K]
   Kernel driver in use: ohci_hcd

00:13.1 USB Controller: ATI Technologies Inc SB7x0 USB OHCI1 Controller (prog-if 10 [OHCI])
   Subsystem: ASRock Incorporation Device 4398
   Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18
   Memory at ff706000 (32-bit, non-prefetchable) [size=4K]
   Kernel driver in use: ohci_hcd

00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
   Subsystem: ASRock Incorporation Device 4396
   Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 19
   Memory at ff705000 (32-bit, non-prefetchable) [size=256]
   Capabilities: [c0] Power Management version 2
   Capabilities: [e4] Debug port: BAR=1 offset=00e0
   Kernel driver in use: ehci_hcd
*snip*
00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller (prog-if 10 [OHCI])
   Subsystem: ASRock Incorporation Device 4399
   Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18
   Memory at ff704000 (32-bit, non-prefetchable) [size=4K]
   Kernel driver in use: ohci_hcd
*snip*
02:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI])
   Flags: bus master, fast devsel, latency 0, IRQ 18
   Memory at ff600000 (64-bit, non-prefetchable) [size=8K]
   Capabilities: [50] Power Management version 3
   Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
   Capabilities: [90] MSI-X: Enable+ Count=8 Masked-
   Capabilities: [a0] Express Endpoint, MSI 00
   Capabilities: [100] Advanced Error Reporting
   Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff
   Capabilities: [150] #18
   Kernel driver in use: xhci_hcd
   Kernel modules: xhci-hcd

03:00.0 USB Controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller (prog-if 30 [XHCI])
   Subsystem: ASRock Incorporation Device 1042
   Flags: bus master, fast devsel, latency 0, IRQ 17
   Memory at ff500000 (64-bit, non-prefetchable) [size=32K]
   Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+
   Capabilities: [68] MSI-X: Enable+ Count=8 Masked-
   Capabilities: [78] Power Management version 3
   Capabilities: [80] Express Legacy Endpoint, MSI 00
   Capabilities: [100] Virtual Channel
   Kernel driver in use: xhci_hcd
   Kernel modules: xhci-hcd
*snip*


I hope someone can shed some light on this.

Greetz,

J@n
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Sun Feb 05, 2012 8:03 am

Well, I have tried a Live CD from OpenSuse 12.1 (KDE). And lo and behold!! Copying just worked. OK, it was not at blazing speed (avg 10 MiB/sec) but still.....it did what it had to do. So no BIOS setting or hardware defect is causing this.

And on a side note, Dolphin looked great compared to Nautilus. Hmmmm, choices, choices.. :wink:

Greetz,

J@N
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Mon Feb 06, 2012 3:03 pm

Hi All Troubled Souls :wink:

Found this is a long running bug in Ubuntu. Philinux (from that "other" forum) pointed me to launchpad where I added myself as being affected by this bug. Please visit https://bugs.launchpad.net/ubuntu/+sour ... bug/500069 , register if needed and add yourself to the list. The more the marier :?

Greetz,

J@n
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top

Re: Copy to USB devices slow and problematic

Postby soulrain on Fri Feb 10, 2012 11:19 pm

Same problem...taking days to copy a movie over to a usb drive that used to take minutes under win 7...

So the concensus is to reinstall another distro of linux?

So everyone has this problem?
soulrain
Level 1
Level 1
 
Posts: 23
Joined: Sun Feb 05, 2012 9:07 pm
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Sat Feb 11, 2012 4:47 am

Hi soulrain,

No concensus as far as I am concerned. I would prefer to stay with Minty if I can.

It seems to be solved in the next Ubuntu release (12.04?) with kernel 3.2.0. At least that's what I read here: https://bugs.launchpad.net/ubuntu/+sour ... omments/51

I am not enough of a Linux buff to know if it would be possible to use this kernel in my current Mint installation. Would be nice though :)

Greetz,

J@n
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top

Re: Copy to USB devices slow and problematic

Postby soulrain on Sat Feb 11, 2012 1:56 pm

Thanks for the reply... When is that next kernel due out?

Want to here my relatively ghetto work around?

I have a vm winxp64 running on one box, and use drop box so that windows can be used to put files to usb devices.

I should have left dual boot with windows on one of my boxes but I so just wanted to force myself to use linux.
soulrain
Level 1
Level 1
 
Posts: 23
Joined: Sun Feb 05, 2012 9:07 pm
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Sun Feb 12, 2012 7:21 am

soulrain wrote:When is that next kernel due out?


Hi soulrain,

I expect the new kernel (3.2) to be out in April 2012. Most probably the end of April.

I Like your workaround but it does not work for me (Win 7 64bit in a VirtualBox 4.1.8)

Greetz,

J@n
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top

Re: Copy to USB devices slow and problematic

Postby soulrain on Sun Feb 12, 2012 5:20 pm

J@n wrote:
soulrain wrote:When is that next kernel due out?


Hi soulrain,

I expect the new kernel (3.2) to be out in April 2012. Most probably the end of April.

I Like your workaround but it does not work for me (Win 7 64bit in a VirtualBox 4.1.8)

Greetz,

J@n



Thanks for the info J@n!
soulrain
Level 1
Level 1
 
Posts: 23
Joined: Sun Feb 05, 2012 9:07 pm
Top

Re: Copy to USB devices slow and problematic

Postby Detonate on Mon Feb 13, 2012 8:44 am

I am not having any problem with copying files to a USB device, but from reading this I am wondering if perhaps it could be a permissions problem. What happens if you try to copy as sudo?
Image
User avatar
Detonate
Level 2
Level 2
 
Posts: 85
Joined: Fri Oct 14, 2011 7:40 pm
Location: Ault, Colorado
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Mon Feb 13, 2012 10:41 am

Hi Detonate,

Thanks for your interest in our problem.

Just tried to copy files as sudo using
Code: Select all
gksu nautilus


It still takes about 1.5 to 2 minutes to start the copy of a file after the previous one has been comleted. Although it does look better (copying continues) it still takes ages to complete the command.

Greetz,

J@n
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top

Re: Copy to USB devices slow and problematic

Postby Detonate on Mon Feb 13, 2012 11:00 am

Is there a difference if you don't use Nautilus?

Try using the copy command instead.

Code: Select all
sudo cp /filetobecopied /dev/nameofdevice
Image
User avatar
Detonate
Level 2
Level 2
 
Posts: 85
Joined: Fri Oct 14, 2011 7:40 pm
Location: Ault, Colorado
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Mon Feb 13, 2012 11:29 am

Hi Detonate,

I tried this:
Code: Select all
sudo cp * /dev/sdi1
from within the folder of the files I want to copy. Note that sdi1 is the USB device I want to use. I get this response:
Code: Select all
cp: target `/dev/sdi1' is not a directory
So next I issued this command:
Code: Select all
sudo cp * /media/KINGSTON
It is still copying as I type. So it seems that there is no difference copying from Nautlius or from cli.

Note that I am using an AMD chipset (AMD SB710) with an additional chipset for USB 3.0 (ASMedia ASM1042). The problem is present on both chips.

Thanks again!

Greetz,

J@n
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top

Re: Copy to USB devices slow and problematic

Postby Detonate on Mon Feb 13, 2012 11:58 am

By trying from the command line with the same results, it is obvious that the problem does not lie with Nautilus. I have no further suggestions, hope this gets fixed by a system update.
Image
User avatar
Detonate
Level 2
Level 2
 
Posts: 85
Joined: Fri Oct 14, 2011 7:40 pm
Location: Ault, Colorado
Top

Re: Copy to USB devices slow and problematic

Postby J@n on Mon Feb 13, 2012 12:18 pm

Hi Detonate,

Thanks for trying. Your help is much appreciated!

Greetz,

J@n
AMD Phenom II X4 975 - 16 GB DDR3-1033 - 55 GB SSD - 1.5 TB HDD - 2 TB HDD - Mint 13

If it don't fit use a hammer
J@n
Level 1
Level 1
 
Posts: 25
Joined: Thu Nov 10, 2011 4:10 pm
Top
Linux Mint is funded by ads and donations.
 
Top
Next
Post a reply

Return to Hardware Support

Who is online

Users browsing this forum: No registered users and 20 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group