After I update to mint 14 (KDE), only running
sudo /usr/lib/linuxmint/mintWifi/mintWifi.py
will make wifi internet work.
It can connect to the wireless spot, but cannot open any URL... I think its dclient problem...
how could I fix this issue?
after update, wifi only work after run mintWifi.py
Forum rules
Before you post read how to get help. Topics in this forum are automatically closed 6 months after creation.
Before you post read how to get help. Topics in this forum are automatically closed 6 months after creation.
-
KammutierSpule
- Level 1
- Posts: 19
- Joined: Mon Mar 28, 2011 3:27 pm
after update, wifi only work after run mintWifi.py
Last edited by LockBot on Wed Dec 28, 2022 7:16 am, edited 1 time in total.
Reason: Topic automatically closed 6 months after creation. New replies are no longer allowed.
Reason: Topic automatically closed 6 months after creation. New replies are no longer allowed.
-
k0rben
Re: after update, wifi only work after run mintWifi.py
exactly the same problem, really annoying...
-
KammutierSpule
- Level 1
- Posts: 19
- Joined: Mon Mar 28, 2011 3:27 pm
Re: after update, wifi only work after run mintWifi.py
Sill not solved..
I found that when I am connect, if I reboot and connect in the same wifi it will work, if I change to other place with other wifi.. I need to run mintWifi.py :S
I found that when I am connect, if I reboot and connect in the same wifi it will work, if I change to other place with other wifi.. I need to run mintWifi.py :S
-------------------------
* I. scanning WIFI PCI devices...
-- Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
==> PCI ID = 8086:4229 (rev 61)
-------------------------
* II. querying ndiswrapper...
-------------------------
* III. querying iwconfig...
wlan0 IEEE 802.11abgn ESSID:"AdegaRI"
Mode:Managed Frequency:2.412 GHz Access Point: 00:78:9E:FB:7C:6B
Bit Rate=72.2 Mb/s Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=67/70 Signal level=-43 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:912 Invalid misc:262 Missed beacon:0
lo no wireless extensions.
eth0 no wireless extensions.
-------------------------
* IV. querying ifconfig...
eth0 Link encap:Ethernet Endereço de HW 00:1e:ec:a2:a1:6c
UP BROADCAST MULTICAST MTU:1500 Métrica:1
pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0
Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0
colisões:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
IRQ:22 Memória:e4620000-e4640000
lo Link encap:Loopback Local
inet end.: 127.0.0.1 Masc:255.0.0.0
endereço inet6: ::1/128 Escopo:Máquina
UP LOOPBACK RUNNING MTU:16436 Métrica:1
pacotes RX:40 erros:0 descartados:0 excesso:0 quadro:0
Pacotes TX:40 erros:0 descartados:0 excesso:0 portadora:0
colisões:0 txqueuelen:0
RX bytes:3462 (3.4 KB) TX bytes:3462 (3.4 KB)
wlan0 Link encap:Ethernet Endereço de HW 00:21:5c:09:53:8f
inet end.: 192.168.1.24 Bcast:192.168.1.255 Masc:255.255.255.0
endereço inet6: fe80::221:5cff:fe09:538f/64 Escopo:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Métrica:1
pacotes RX:11647 erros:0 descartados:0 excesso:0 quadro:0
Pacotes TX:6629 erros:0 descartados:0 excesso:0 portadora:0
colisões:0 txqueuelen:1000
RX bytes:8365410 (8.3 MB) TX bytes:1353205 (1.3 MB)
-------------------------
* V. querying DHCP...
Rather than invoking init scripts through /etc/init.d, use the service(8)
utility, e.g. service smbd reload
Since the script you are attempting to invoke has been converted to an
Upstart job, you may also use the reload(8) utility, e.g. reload smbd
RTNETLINK answers: File exists
-------------------------
* VI. querying nslookup google.com...
Server: 213.228.128.156
Address: 213.228.128.156#53
Non-authoritative answer:
Name: google.com
Address: 173.194.45.14
....