guest Linux Mint 18 Sarah
I have tried everything I found on the web but it is still not working.
I tried to set autoneg to off with ethtool, but the setting is not changing. Restarted the interface (worked with ifconfig, ifup and ifdown return 'unknown interface').
With 'sudo nano /etc/rc.local' I have set autoneg to off and speed to 100. As you can see below, it says 'Link detected yes' , but still not working.
I have switched between NAT and bridged and rebooted a lot of times , at bridged I used the option promiscuous mode off and 'allow vms'.
I have set DNS to 8.8.8.8 and 208.67.222.222 and 208.67.220.220.
Nothing of this worked, it still does not get internet.. I have ran out of ideas and would appreciate any hints what else can be tried to get the internet working on the guest VM.
Here is information about the network interface and also the output of inxi -Fxz on the guest :
/sbin/ifconfig -a
Code: Select all
enp0s3 Link encap:Ethernet HWaddr 08:00:27:ef:d1:e4
inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0
inet6 addr: fe80::b9c4:5463:5b1:1650/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:35 errors:0 dropped:0 overruns:0 frame:0
TX packets:165 errors:25 dropped:0 overruns:0 carrier:4
collisions:0 txqueuelen:1000
RX bytes:11125 (11.1 KB) TX bytes:49712 (49.7 KB)
Interrupt:9 Base address:0xd020
ethtool enp0s3:
Code: Select all
Settings for enp0s3:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Cannot get wake-on-lan settings: Operation not permitted
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
inxi -Fxz
Code: Select all
System: Host: LinuxMint Kernel: 4.4.0-21-generic i686 (32 bit gcc: 5.3.1)
Desktop: Xfce 4.12.3 (Gtk 2.24.28) Distro: Linux Mint 18 Sarah
Machine: System: innotek (portable) product: VirtualBox v: 1.2
Mobo: Oracle model: VirtualBox v: 1.2
Bios: innotek v: VirtualBox date: 12/01/2006
CPU: Single core Intel Core i5-5300U (-UP-) cache: 3072 KB
flags: (nx pae sse sse2 sse3 sse4_1 sse4_2 ssse3) bmips: 4589 speed: 2294 MHz (max)
Graphics: Card: InnoTek Systemberatung VirtualBox Graphics Adapter
bus-ID: 00:02.0
Display Server: X.Org 1.18.3 drivers: vboxvideo (unloaded: fbdev,vesa)
Resolution: 1496x724@59.85hz
GLX Renderer: Gallium 0.4 on llvmpipe (LLVM 3.8, 256 bits)
GLX Version: 3.0 Mesa 11.2.0 Direct Rendering: Yes
Audio: Card Intel 82801AA AC'97 Audio Controller
driver: snd_intel8x0 ports: d100 d200 bus-ID: 00:05.0
Sound: Advanced Linux Sound Architecture v: k4.4.0-21-generic
Network: Card: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE]
driver: pcnet32 port: d020 bus-ID: 00:03.0
IF: enp0s3 state: up speed: 100 Mbps duplex: full mac: <filter>
Drives: HDD Total Size: 10.7GB (54.0% used)
ID-1: /dev/sda model: VBOX_HARDDISK size: 10.7GB
Partition: ID-1: / size: 8.7G used: 4.4G (54%) fs: ext4 dev: /dev/sda1
ID-2: swap-1 size: 1.21GB used: 0.00GB (0%) fs: swap dev: /dev/sda5
RAID: No RAID devices: /proc/mdstat, md_mod kernel module present
Sensors: None detected - is lm-sensors installed and configured?
Info: Processes: 170 Uptime: 48 min Memory: 376.8/1019.2MB
Init: systemd runlevel: 5 Gcc sys: 5.3.1