so I tried to mount an USB drive, but when I plug it in nothing happens. This happens only on Linux, if i boot my windows partition everything's fine.
Also, when I unplug the USB drive, then plug it in again, lsusb doesn't work anymore and if I unplug it again, the computer freezes.
This is the (possibly) relevant output of dmesg:
Code: Select all
[ 18.458655] usb 1-1: new high-speed USB device number 6 using xhci_hcd
[ 18.654933] usb 1-1: New USB device found, idVendor=058f, idProduct=6387
[ 18.654940] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 18.654945] usb 1-1: Product: Mass Storage Device
[ 18.654949] usb 1-1: Manufacturer: JetFlash
[ 18.654952] usb 1-1: SerialNumber: 7295ZN5X
[ 18.655676] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 18.655989] usb-storage 1-1:1.0: Quirks match for vid 058f pid 6387: 400
[ 18.656124] scsi7 : usb-storage 1-1:1.0
[ 19.653612] xhci_hcd 0000:00:14.0: ERROR Unknown event condition, HC probably busted
[ 40.854987] usb 1-1: reset high-speed USB device number 6 using xhci_hcd
[ 41.049817] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88042a1cb208
[ 129.148728] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 129.151019] JFS: nTxBlock = 8192, nTxLock = 65536
[ 129.157238] ntfs: driver 2.1.30 [Flags: R/W MODULE].
[ 129.162019] QNX4 filesystem 0.2.3 registered.
[ 129.232384] raid6: sse2x1 9413 MB/s
[ 129.300314] raid6: sse2x2 10954 MB/s
[ 129.368237] raid6: sse2x4 11538 MB/s
[ 129.436166] raid6: avx2x1 17696 MB/s
[ 129.504092] raid6: avx2x2 26377 MB/s
[ 129.572019] raid6: avx2x4 32818 MB/s
[ 129.572020] raid6: using algorithm avx2x4 (32818 MB/s)
[ 129.572021] raid6: using avx2x2 recovery algorithm
[ 129.574526] xor: automatically using best checksumming function:
[ 129.611976] avx : 34369.000 MB/sec
[ 129.617361] Btrfs loaded
Code: Select all
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 005: ID 046d:c52e Logitech, Inc.
Bus 001 Device 004: ID 05e3:070e Genesys Logic, Inc. USB 2.0 Card Reader
Bus 001 Device 003: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 001 Device 002: ID 1395:0025 Sennheiser Communications
Bus 001 Device 006: ID 058f:6387 Alcor Micro Corp. Flash Drive
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
And here's fdisk -l:
Code: Select all
Disk /dev/sda: 931,5 GiB, 1000204886016 bytes, 1953525168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00021e85
Device Boot Start End Sectors Size Id Type
/dev/sda1 * 2048 1026047 1024000 500M 7 HPFS/NTFS/exFAT
/dev/sda2 1026048 929521663 928495616 442,8G 7 HPFS/NTFS/exFAT
/dev/sda3 929521664 1953523711 1024002048 488,3G 5 Extended
/dev/sda5 929523712 1056499711 126976000 60,6G 83 Linux
/dev/sda6 1920755712 1953523711 32768000 15,6G 83 Linux
/dev/sda7 1056501760 1920753663 864251904 412,1G 83 Linux
Partition table entries are not in disk order.
Disk /dev/sdb: 1,8 TiB, 2000398934016 bytes, 3907029168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: B17B6CBE-29CD-4C42-892A-EA0E6A69719A
Device Start End Sectors Size Type
/dev/sdb1 64 8191 8128 4M EFI System
/dev/sdb2 8224 520191 511968 250M Microsoft basic data
/dev/sdb3 520224 1032191 511968 250M Microsoft basic data
/dev/sdb4 1032224 1257471 225248 110M unknown
/dev/sdb5 1257504 1843199 585696 286M Microsoft basic data
/dev/sdb6 1843200 7086079 5242880 2,5G unknown
/dev/sdb7 7086080 15472639 8386560 4G Microsoft basic data
/dev/sdb8 15472640 3907026943 3891554304 1,8T Microsoft basic data
Any ideas how to fix that?
Thanks.