System info
Code: Select all
System:
Kernel: 5.15.0-56-generic x86_64 bits: 64 compiler: gcc v: 11.3.0 Desktop: Cinnamon 5.4.12
tk: GTK 3.24.33 wm: Mutter dm: LightDM Distro: Linux Mint 21 Vanessa base: Ubuntu 22.04 jammy
Machine:
Type: Laptop System: Dell product: XPS 17 9720 v: N/A serial: <superuser required> Chassis:
type: 10 serial: <superuser required>
Mobo: Dell model: 0W7GHH v: A00 serial: <superuser required> UEFI: Dell v: 1.4.0
date: 03/08/2022
Battery:
ID-1: BAT0 charge: 77.3 Wh (89.8%) condition: 86.1/95.1 Wh (90.6%) volts: 12.2 min: 11.4
model: BYD DELL F8CPG21 serial: <filter> status: Discharging
CPU:
Info: 14-core (6-mt/8-st) model: 12th Gen Intel Core i9-12900HK bits: 64 type: MST AMCP
arch: Alder Lake rev: 3 cache: L1: 1.2 MiB L2: 11.5 MiB L3: 24 MiB
Speed (MHz): avg: 830 high: 1098 min/max: 400/5000:3800 cores: 1: 1046 2: 798 3: 840 4: 1098
5: 645 6: 748 7: 615 8: 731 9: 924 10: 671 11: 971 12: 815 13: 1026 14: 856 15: 712 16: 955
17: 750 18: 893 19: 839 20: 668 bogomips: 116736
Flags: avx avx2 ht lm nx pae sse sse2 sse3 sse4_1 sse4_2 ssse3 vmx
Graphics:
Device-1: Intel Alder Lake-P Integrated Graphics vendor: Dell driver: i915 v: kernel ports:
active: DP-2 off: eDP-1 empty: DP-1, DP-3, DP-4, DP-5, HDMI-A-1 bus-ID: 0000:00:02.0
chip-ID: 8086:46a6
Device-2: NVIDIA GA106M [GeForce RTX 3060 Mobile / Max-Q] vendor: Dell driver: nvidia
v: 525.60.11 ports: active: none empty: DP-6, DP-7, DP-8, DP-9 bus-ID: 0000:01:00.0
chip-ID: 10de:2520
Device-3: Microdia Integrated_Webcam_HD type: USB driver: uvcvideo bus-ID: 1-6:6
chip-ID: 0c45:6d1f
Display: x11 server: X.Org v: 1.21.1.3 driver: X: loaded: modesetting,nvidia
unloaded: fbdev,nouveau,vesa gpu: i915 display-ID: :0 screens: 1
Screen-1: 0 s-res: 2560x1440 s-dpi: 96
Monitor-1: DP-1-2 mapped: DP-2 model: Dell U2715H res: 2560x1440 dpi: 109 diag: 685mm (27")
OpenGL: renderer: NVIDIA GeForce RTX 3060 Laptop GPU/PCIe/SSE2 v: 4.6.0 NVIDIA 525.60.11
direct render: Yes
Audio:
Device-1: Intel Alder Lake PCH-P High Definition Audio vendor: Dell
driver: sof-audio-pci-intel-tgl bus-ID: 0000:00:1f.3 chip-ID: 8086:51c8
Device-2: NVIDIA vendor: Dell driver: snd_hda_intel v: kernel bus-ID: 0000:01:00.1
chip-ID: 10de:228e
Device-3: SteelSeries ApS Arctis 5 type: USB driver: hid-generic,snd-usb-audio,usbhid
bus-ID: 1-2.4:5 chip-ID: 1038:12aa
Sound Server-1: ALSA v: k5.15.0-56-generic running: yes
Sound Server-2: PulseAudio v: 15.99.1 running: yes
Sound Server-3: PipeWire v: 0.3.48 running: yes
Network:
Device-1: Intel Alder Lake-P PCH CNVi WiFi driver: iwlwifi v: kernel bus-ID: 0000:00:14.3
chip-ID: 8086:51f0
IF: wlp0s20f3 state: up mac: <filter>
Device-2: ASIX AX88179 Gigabit Ethernet type: USB driver: ax88179_178a bus-ID: 4-1.3:4
chip-ID: 0b95:1790
IF: enxf8e43bce5c6b state: down mac: <filter>
IF-ID-1: docker0 state: down mac: <filter>
Bluetooth:
Device-1: Intel type: USB driver: btusb v: 0.8 bus-ID: 1-10:10 chip-ID: 8087:0033
Report: hciconfig ID: hci0 rfk-id: 1 state: down bt-service: enabled,running rfk-block:
hardware: no software: yes address: <filter>
RAID:
Hardware-1: Intel Volume Management Device NVMe RAID Controller driver: vmd v: 0.6
bus-ID: 0000:00:0e.0 chip-ID: 8086:467f
Drives:
Local Storage: total: 1.86 TiB used: 109.14 GiB (5.7%)
ID-1: /dev/nvme0n1 vendor: Samsung model: PM9A1 NVMe 1024GB size: 953.87 GiB speed: 63.2 Gb/s
lanes: 4 serial: <filter> temp: 33.9 C
ID-2: /dev/nvme1n1 vendor: Western Digital model: PC SN810 NVMe WDC 1024GB size: 953.87 GiB
speed: 63.2 Gb/s lanes: 4 serial: <filter> temp: 31.9 C
Partition:
ID-1: / size: 228.19 GiB used: 109.09 GiB (47.8%) fs: ext4 dev: /dev/nvme0n1p5
ID-2: /boot/efi size: 96 MiB used: 49.1 MiB (51.1%) fs: vfat dev: /dev/nvme0n1p1
Swap:
ID-1: swap-1 type: file size: 2 GiB used: 0 KiB (0.0%) priority: -2 file: /swapfile
Sensors:
System Temperatures: cpu: 42.0 C mobo: N/A gpu: nvidia temp: 44 C
Fan Speeds (RPM): N/A
Repos:
Packages: 2725 apt: 2706 flatpak: 7 snap: 12
No active apt repos in: /etc/apt/sources.list
Active apt repos in: /etc/apt/sources.list.d/additional-repositories.list
1: deb [arch=amd64,arm64,ppc64el] https: //mariadb.mirror.liquidtelecom.com/repo/10.6/ubuntu focal main
2: deb [arch=amd64] https: //download.docker.com/linux/ubuntu jammy stable
Active apt repos in: /etc/apt/sources.list.d/google-chrome.list
1: deb [arch=amd64] https: //dl.google.com/linux/chrome/deb/ stable main
Active apt repos in: /etc/apt/sources.list.d/google-cloud-sdk.list
1: deb [signed-by=/usr/share/keyrings/cloud.google.gpg] https: //packages.cloud.google.com/apt cloud-sdk main
Active apt repos in: /etc/apt/sources.list.d/linuxuprising-java-jammy.list
1: deb http: //ppa.launchpad.net/linuxuprising/java/ubuntu jammy main
Active apt repos in: /etc/apt/sources.list.d/official-package-repositories.list
1: deb https: //ftp.icm.edu.pl/pub/Linux/dist/linuxmint/packages vanessa main upstream import backport
2: deb http: //mirror.mirohost.net/ubuntu jammy main restricted universe multiverse
3: deb http: //mirror.mirohost.net/ubuntu jammy-updates main restricted universe multiverse
4: deb http: //mirror.mirohost.net/ubuntu jammy-backports main restricted universe multiverse
5: deb http: //security.ubuntu.com/ubuntu/ jammy-security main restricted universe multiverse
Active apt repos in: /etc/apt/sources.list.d/opera-stable.list
1: deb https: //deb.opera.com/opera-stable/ stable non-free
Active apt repos in: /etc/apt/sources.list.d/skype-stable.list
1: deb [arch=amd64] https: //repo.skype.com/deb stable main
Active apt repos in: /etc/apt/sources.list.d/slack.list
1: deb https: //packagecloud.io/slacktechnologies/slack/debian/ jessie main
Active apt repos in: /etc/apt/sources.list.d/sublime-text.list
1: deb https: //download.sublimetext.com/ apt/stable/
Active apt repos in: /etc/apt/sources.list.d/teamviewer.list
1: deb [signed-by=/usr/share/keyrings/teamviewer-keyring.gpg] https: //linux.teamviewer.com/deb stable main
Info:
Processes: 479 Uptime: 14m Memory: 62.5 GiB used: 8.62 GiB (13.8%) Init: systemd v: 249
runlevel: 5 Compilers: gcc: 11.3.0 alt: 11 Client: Cinnamon v: 5.4.12 inxi: 3.3.13
Code: Select all
# ------------------------------------------------------------------------------
# tlp - Parameters for power saving
# See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html
# Hint: some features are disabled by default, remove the leading # to enable
# them.
# Set to 0 to disable, 1 to enable TLP.
TLP_ENABLE=1
# Operation mode when no power supply can be detected: AC, BAT.
# Concerns some desktop and embedded hardware only.
TLP_DEFAULT_MODE=BAT
# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE
# Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC.
TLP_PERSISTENT_DEFAULT=0
# Seconds laptop mode has to wait after the disk goes idle before doing a sync.
# Non-zero value enables, zero disables laptop mode.
DISK_IDLE_SECS_ON_AC=0
DISK_IDLE_SECS_ON_BAT=2
# Dirty page values (timeouts in secs).
MAX_LOST_WORK_SECS_ON_AC=15
MAX_LOST_WORK_SECS_ON_BAT=60
# Hint: CPU parameters below are disabled by default, remove the leading #
# to enable them, otherwise kernel default values are used.
# Select a CPU frequency scaling governor.
# Intel Core i processor with intel_pstate driver:
# powersave(*), performance.
# Older hardware with acpi-cpufreq driver:
# ondemand(*), powersave, performance, conservative, schedutil.
# (*) is recommended.
# Hint: use tlp-stat -p to show the active driver and available governors.
# Important:
# powersave for intel_pstate and ondemand for acpi-cpufreq are power
# efficient for *almost all* workloads and therefore kernel and most
# distributions have chosen them as defaults. If you still want to change,
# you should know what you're doing! You *must* disable your distribution's
# governor settings or conflicts will occur.
#CPU_SCALING_GOVERNOR_ON_AC=powersave
CPU_SCALING_GOVERNOR_ON_BAT=powersave
# Set the min/max frequency available for the scaling governor.
# Possible values strongly depend on your CPU. For available frequencies see
# the output of tlp-stat -p.
CPU_SCALING_MIN_FREQ_ON_AC=0
CPU_SCALING_MAX_FREQ_ON_AC=3800000
CPU_SCALING_MIN_FREQ_ON_BAT=0
CPU_SCALING_MAX_FREQ_ON_BAT=2000000
# Set energy performance hints (HWP) for Intel P-state governor:
# performance, balance_performance, default, balance_power, power
# Values are given in order of increasing power saving.
# Note: Intel Skylake or newer CPU and Kernel >= 4.10 required.
CPU_HWP_ON_AC=balance_performance
CPU_HWP_ON_BAT=balance_power
# Set Intel P-state performance: 0..100 (%).
# Limit the max/min P-state to control the power dissipation of the CPU.
# Values are stated as a percentage of the available performance.
# Requires an Intel Core i processor with intel_pstate driver.
CPU_MIN_PERF_ON_AC=0
CPU_MAX_PERF_ON_AC=100
CPU_MIN_PERF_ON_BAT=0
CPU_MAX_PERF_ON_BAT=30
# Set the CPU "turbo boost" feature: 0=disable, 1=allow
# Requires an Intel Core i processor.
# Important:
# - This may conflict with your distribution's governor settings
# - A value of 1 does *not* activate boosting, it just allows it
CPU_BOOST_ON_AC=1
CPU_BOOST_ON_BAT=0
# Minimize number of used CPU cores/hyper-threads under light load conditions:
# 0=disable, 1=enable.
SCHED_POWERSAVE_ON_AC=0
SCHED_POWERSAVE_ON_BAT=1
# Kernel NMI Watchdog:
# 0=disable (default, saves power), 1=enable (for kernel debugging only).
NMI_WATCHDOG=0
# Change CPU voltages aka "undervolting" - Kernel with PHC patch required.
# Frequency voltage pairs are written to:
# /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
# CAUTION: only use this, if you thoroughly understand what you are doing!
#PHC_CONTROLS="F:V F:V F:V F:V"
# Set CPU performance versus energy savings policy:
# performance, balance-performance, default, balance-power, power.
# Values are given in order of increasing power saving.
# Requires kernel module msr and x86_energy_perf_policy from linux-tools.
ENERGY_PERF_POLICY_ON_AC=performance
ENERGY_PERF_POLICY_ON_BAT=power
# Disk devices; separate multiple devices with spaces (default: sda).
# Devices can be specified by disk ID also (lookup with: tlp diskid).
DISK_DEVICES="sda sdb"
# Disk advanced power management level: 1..254, 255 (max saving, min, off).
# Levels 1..127 may spin down the disk; 255 allowable on most drives.
# Separate values for multiple disks with spaces. Use the special value 'keep'
# to keep the hardware default for the particular disk.
DISK_APM_LEVEL_ON_AC="254 254"
DISK_APM_LEVEL_ON_BAT="128 128"
# Hard disk spin down timeout:
# 0: spin down disabled
# 1..240: timeouts from 5s to 20min (in units of 5s)
# 241..251: timeouts from 30min to 5.5 hours (in units of 30min)
# See 'man hdparm' for details.
# Separate values for multiple disks with spaces. Use the special value 'keep'
# to keep the hardware default for the particular disk.
#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0"
#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"
# Select IO scheduler for the disk devices: cfq, deadline, noop (Default: cfq).
# Separate values for multiple disks with spaces. Use the special value 'keep'
# to keep the kernel default scheduler for the particular disk.
#DISK_IOSCHED="cfq cfq"
# AHCI link power management (ALPM) for disk devices:
# min_power, med_power_with_dipm(*), medium_power, max_performance.
# (*) Kernel >= 4.15 required, then recommended.
# Multiple values separated with spaces are tried sequentially until success.
SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance"
SATA_LINKPWR_ON_BAT="min_power"
# Exclude host devices from AHCI link power management.
# Separate multiple hosts with spaces.
#SATA_LINKPWR_BLACKLIST="host1"
# Runtime Power Management for AHCI host and disks devices:
# on=disable, auto=enable.
# EXPERIMENTAL ** WARNING: auto will most likely cause system lockups/data loss.
#AHCI_RUNTIME_PM_ON_AC=on
#AHCI_RUNTIME_PM_ON_BAT=on
# Seconds of inactivity before disk is suspended.
AHCI_RUNTIME_PM_TIMEOUT=15
# PCI Express Active State Power Management (PCIe ASPM):
# default, performance, powersave.
PCIE_ASPM_ON_AC=performance
PCIE_ASPM_ON_BAT=powersave
# WiFi power saving mode: on=enable, off=disable; not supported by all adapters.
WIFI_PWR_ON_AC=off
WIFI_PWR_ON_BAT=on
# Disable wake on LAN: Y/N.
WOL_DISABLE=Y
# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
# A value of 0 disables, >=1 enables power saving (recommended: 1).
SOUND_POWER_SAVE_ON_AC=0
SOUND_POWER_SAVE_ON_BAT=1
# Disable controller too (HDA only): Y/N.
SOUND_POWER_SAVE_CONTROLLER=Y
# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable.
RUNTIME_PM_ON_AC=on
RUNTIME_PM_ON_BAT=auto
# Exclude PCI(e) device adresses the following list from Runtime PM
# (separate with spaces). Use lspci to get the adresses (1st column).
#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6"
# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM.
# Default when unconfigured is "amdgpu nouveau nvidia radeon" which
# prevents accidential power-on of dGPU in hybrid graphics setups.
# Use "" to disable the feature completely.
# Separate multiple drivers with spaces.
#RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon"
# Set to 0 to disable, 1 to enable USB autosuspend feature.
USB_AUTOSUSPEND=1
# Exclude listed devices from USB autosuspend (separate with spaces).
# Use lsusb to get the ids.
# Note: input devices (usbhid) are excluded automatically
#USB_BLACKLIST="1111:2222 3333:4444"
# Bluetooth devices are excluded from USB autosuspend:
# 0=do not exclude, 1=exclude.
USB_BLACKLIST_BTUSB=0
# Phone devices are excluded from USB autosuspend:
# 0=do not exclude, 1=exclude (enable charging).
USB_BLACKLIST_PHONE=0
# Printers are excluded from USB autosuspend:
# 0=do not exclude, 1=exclude.
USB_BLACKLIST_PRINTER=1
# WWAN devices are excluded from USB autosuspend:
# 0=do not exclude, 1=exclude.
USB_BLACKLIST_WWAN=1
# Include listed devices into USB autosuspend even if already excluded
# by the blacklists above (separate with spaces).
# Use lsusb to get the ids.
# 138a:0091 - fingerprint sensor
# 04f3:24a1 - touch screen
USB_WHITELIST="138a:0091 04f3:24a1"
# Set to 1 to disable autosuspend before shutdown, 0 to do nothing
# (workaround for USB devices that cause shutdown problems).
#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1
# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
# on system startup: 0=disable, 1=enable.
# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
# are ignored when this is enabled!
RESTORE_DEVICE_STATE_ON_STARTUP=0
# Radio devices to disable on startup: bluetooth, wifi, wwan.
# Separate multiple devices with spaces.
DEVICES_TO_DISABLE_ON_STARTUP="bluetooth"
# Radio devices to enable on startup: bluetooth, wifi, wwan.
# Separate multiple devices with spaces.
#DEVICES_TO_ENABLE_ON_STARTUP="wifi"
# Radio devices to disable on shutdown: bluetooth, wifi, wwan.
# (workaround for devices that are blocking shutdown).
#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"
# Radio devices to enable on shutdown: bluetooth, wifi, wwan.
# (to prevent other operating systems from missing radios).
#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"
# Radio devices to enable on AC: bluetooth, wifi, wwan.
# DEVICES_TO_ENABLE_ON_AC="bluetooth"
# Radio devices to disable on battery: bluetooth, wifi, wwan.
# DEVICES_TO_DISABLE_ON_BAT="bluetooth"
# Radio devices to disable on battery when not in use (not connected):
# bluetooth, wifi, wwan.
#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"
# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module
# required). Charging starts when the remaining capacity falls below the
# START_CHARGE_THRESH value and stops when exceeding the STOP_CHARGE_THRESH value.
# Main / Internal battery (values in %)
#START_CHARGE_THRESH_BAT0=75
#STOP_CHARGE_THRESH_BAT0=80
# Ultrabay / Slice / Replaceable battery (values in %)
#START_CHARGE_THRESH_BAT1=75
#STOP_CHARGE_THRESH_BAT1=80
# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable.
#RESTORE_THRESHOLDS_ON_BAT=1
# ------------------------------------------------------------------------------
# tlp-rdw - Parameters for the radio device wizard
# Possible devices: bluetooth, wifi, wwan.
# Hints:
# - Parameters are disabled by default, remove the leading # to enable them
# - Separate multiple radio devices with spaces
# Radio devices to disable on connect.
#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"
# Radio devices to enable on disconnect.
#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""
# Radio devices to enable/disable when docked.
#DEVICES_TO_ENABLE_ON_DOCK=""
#DEVICES_TO_DISABLE_ON_DOCK=""
# Radio devices to enable/disable when undocked.
#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
#DEVICES_TO_DISABLE_ON_UNDOCK=""
