[solved] dmesg results

Questions about hardware,drivers and peripherals
Forum rules
Before you post please read how to get help
captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

[solved] dmesg results

Post by captcharis » Sat Mar 03, 2018 9:34 am

Hello again guys !!!!

I have some questions about dmseg command and it's printouts
I used "dmesg --level=err,warn | head" and since them when I use dsmeg is printing out only errors and warnings
Is this command format permanent and if yes how can I return it back to normal.

Moreover do you guys know what is this results I have from my dsmeg command

[30175.303304] usb 1-1.5: new full-speed USB device number 104 using ehci-pci
[30175.383314] usb 1-1.5: device descriptor read/64, error -32
[30175.571235] usb 1-1.5: device descriptor read/64, error -32
[30175.759305] usb 1-1.5: new full-speed USB device number 105 using ehci-pci
[30175.839312] usb 1-1.5: device descriptor read/64, error -32
[30176.027290] usb 1-1.5: device descriptor read/64, error -32
[30176.215322] usb 1-1.5: new full-speed USB device number 106 using ehci-pci
[30176.631289] usb 1-1.5: device not accepting address 106, error -32
[30176.711318] usb 1-1.5: new full-speed USB device number 107 using ehci-pci
[30177.127306] usb 1-1.5: device not accepting address 107, error -32
[30177.127509] usb 1-1-port5: unable to enumerate USB device
[30178.503293] usb 1-1.5: new full-speed USB device number 108 using ehci-pci
[30178.583291] usb 1-1.5: device descriptor read/64, error -32
[30178.771261] usb 1-1.5: device descriptor read/64, error -32
[30178.959307] usb 1-1.5: new full-speed USB device number 109 using ehci-pci
[30179.039264] usb 1-1.5: device descriptor read/64, error -32
[30179.227264] usb 1-1.5: device descriptor read/64, error -32
[30179.415281] usb 1-1.5: new full-speed USB device number 110 using ehci-pci
[30179.831310] usb 1-1.5: device not accepting address 110, error -32
[30179.911309] usb 1-1.5: new full-speed USB device number 111 using ehci-pci
[30180.327226] usb 1-1.5: device not accepting address 111, error -32
[30180.327425] usb 1-1-port5: unable to enumerate USB device
[30181.703320] usb 1-1.5: new full-speed USB device number 112 using ehci-pci
[30181.783279] usb 1-1.5: device descriptor read/64, error -32
[30181.971265] usb 1-1.5: device descriptor read/64, error -32
[30182.159286] usb 1-1.5: new full-speed USB device number 113 using ehci-pci
[30182.239286] usb 1-1.5: device descriptor read/64, error -32
[30182.427220] usb 1-1.5: device descriptor read/64, error -32
[30182.615289] usb 1-1.5: new full-speed USB device number 114 using ehci-pci
[30183.031301] usb 1-1.5: device not accepting address 114, error -32
Last edited by captcharis on Tue Mar 06, 2018 10:25 am, edited 1 time in total.

User avatar
ClixTrix
Level 5
Level 5
Posts: 697
Joined: Wed Dec 09, 2015 11:40 am
Location: Columbus, Ohio, USA

Re: dmesg results

Post by ClixTrix » Sat Mar 03, 2018 9:55 am

device descriptor read/64, error -32

The error can indicate too much power draw from the USB ports. Try disconnecting devices and/or use a powered external USB Hub.

https://askubuntu.com/questions/341241/ ... oes-this-m
Linux Mint 18.3 x64 Cinnamon Kernel 4.15.0-23-generic
Gigabyte GA-AB350M-D3H (F20) / Ryzen 5 1600 / Micron Ballistix Sport DDR4 2400 2x8GB / XFX HD5450-1GB
NVMe-SSD Samsung EVO 960 250GB / SATA-HDD WD1600BEKT 160GB / SATA-SSD Toshiba OCZ VX500 512GB

captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

Re: dmesg results

Post by captcharis » Sat Mar 03, 2018 10:16 am

Thanks a lot my friend
Issue is that I have nothing connect on my USBs, there is a built in camera which is not working
and I though that this was the problem.
Anyway thanks for your time and the link.

C u around!!!
el pueblo unido jamás será vencido

User avatar
ClixTrix
Level 5
Level 5
Posts: 697
Joined: Wed Dec 09, 2015 11:40 am
Location: Columbus, Ohio, USA

Re: dmesg results

Post by ClixTrix » Sat Mar 03, 2018 10:31 am

OK, let's see what's drawing power. Please run the following command from Terminal and post back the results. Note, using sudo will require the admin password.

Code: Select all

sudo lsusb -v
Linux Mint 18.3 x64 Cinnamon Kernel 4.15.0-23-generic
Gigabyte GA-AB350M-D3H (F20) / Ryzen 5 1600 / Micron Ballistix Sport DDR4 2400 2x8GB / XFX HD5450-1GB
NVMe-SSD Samsung EVO 960 250GB / SATA-HDD WD1600BEKT 160GB / SATA-SSD Toshiba OCZ VX500 512GB

captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

Re: dmesg results

Post by captcharis » Sat Mar 03, 2018 10:48 am

is a f**king long list
I tried to make it .txt but i couldn't uploaded.
Here it is, sorry :?

bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x8087 Intel Corp.
idProduct 0x0024 Integrated Rate Matching Hub
bcdDevice 0.00
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 12
Hub Descriptor:
bLength 11
bDescriptorType 41
nNbrPorts 8
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00 0x00
PortPwrCtrlMask 0xff 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0103 power enable connect
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered

Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.13
iManufacturer 3 Linux 4.13.0-32-generic ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:1d.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x02
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered

Bus 001 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. RTS5129 Card Reader Controller
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
idVendor 0x0bda Realtek Semiconductor Corp.
idProduct 0x0129 RTS5129 Card Reader Controller
bcdDevice 39.60
iManufacturer 1 Generic
iProduct 2 USB2.0-CRW
iSerial 3 20100201396000000
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 CARD READER
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 6
bInterfaceProtocol 80
iInterface 5 Bulk-In, Bulk-Out, Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0003 1x 3 bytes
bInterval 10
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)

Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x8087 Intel Corp.
idProduct 0x0024 Integrated Rate Matching Hub
bcdDevice 0.00
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0503 highspeed power enable connect
Port 4: 0000.0100 power
Port 5: 0000.0101 power connect
Port 6: 0000.0100 power
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.13
iManufacturer 3 Linux 4.13.0-32-generic ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:1a.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x02
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Port 2: 0000.0100 power
Device Status: 0x0001
Self Powered

Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 3
bMaxPacketSize0 9
idVendor 0x1d6b Linux Foundation
idProduct 0x0003 3.0 root hub
bcdDevice 4.13
iManufacturer 3 Linux 4.13.0-32-generic xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:14.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 31
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
bMaxBurst 0
Hub Descriptor:
bLength 12
bDescriptorType 42
nNbrPorts 4
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
bHubDecLat 0.0 micro seconds
wHubDelay 0 nano seconds
DeviceRemovable 0x00
Hub Port Status:
Port 1: 0000.02a0 5Gbps power Rx.Detect
Port 2: 0000.02a0 5Gbps power Rx.Detect
Port 3: 0000.02a0 5Gbps power Rx.Detect
Port 4: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 15
bNumDeviceCaps 1
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x0008
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 3
Lowest fully-functional device speed is SuperSpeed (5Gbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 512 micro seconds
Device Status: 0x0001
Self Powered

Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.13
iManufacturer 3 Linux 4.13.0-32-generic xhci-hcd
iProduct 2 xHCI Host Controller
iSerial 1 0000:00:14.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Device Status: 0x0001
Self Powered
el pueblo unido jamás será vencido

User avatar
ClixTrix
Level 5
Level 5
Posts: 697
Joined: Wed Dec 09, 2015 11:40 am
Location: Columbus, Ohio, USA

Re: dmesg results

Post by ClixTrix » Sat Mar 03, 2018 11:30 am

Well, the original post had the problem device on USB 1-1 Port 5.

The listing you posted back appears to be cut-off at the top. However, it does show something powered at Port 5.

Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0103 power enable connect
Port 6: 0000.0100 power
Port 7: 0000.0100 power
Port 8: 0000.0100 power


I don't see the USB Cam, which might be the problem device. Can you disable the USB Cam in BIOS and recheck for the DMESG errors?

I do see a USB RTS5129 Card Reader Controller at Bus 1 Device 3.
Linux Mint 18.3 x64 Cinnamon Kernel 4.15.0-23-generic
Gigabyte GA-AB350M-D3H (F20) / Ryzen 5 1600 / Micron Ballistix Sport DDR4 2400 2x8GB / XFX HD5450-1GB
NVMe-SSD Samsung EVO 960 250GB / SATA-HDD WD1600BEKT 160GB / SATA-SSD Toshiba OCZ VX500 512GB

captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

Re: dmesg results

Post by captcharis » Sun Mar 04, 2018 1:49 am

Hi again Clix and thank you for your time
I did it my friend. I disable my build in web camera , i found something "Integrate NIC" in BIOS menu and I supposed that this sould be the cam!! :D
Actually I was pretty sure that this was the problem but unfortunately some results fro DMESG come back.
Yes, its true are not some like original post , I dont know why. Anyways check below results after web cam disample.
Attachments
Screenshot at 2018-03-04 06-58-15.jpg
el pueblo unido jamás será vencido

User avatar
ClixTrix
Level 5
Level 5
Posts: 697
Joined: Wed Dec 09, 2015 11:40 am
Location: Columbus, Ohio, USA

Re: dmesg results

Post by ClixTrix » Sun Mar 04, 2018 9:12 am

Integrated NIC in BIOS is probably the ethernet port.

I'd like to get more info on your system. Could you please run the following command from Terminal and post back the results.

Code: Select all

inxi -Fxz
Linux Mint 18.3 x64 Cinnamon Kernel 4.15.0-23-generic
Gigabyte GA-AB350M-D3H (F20) / Ryzen 5 1600 / Micron Ballistix Sport DDR4 2400 2x8GB / XFX HD5450-1GB
NVMe-SSD Samsung EVO 960 250GB / SATA-HDD WD1600BEKT 160GB / SATA-SSD Toshiba OCZ VX500 512GB

captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

Re: dmesg results

Post by captcharis » Sun Mar 04, 2018 1:01 pm

Here you are !!!

System: Host: CaptaCharis-Inspiron-5323 Kernel: 4.13.0-32-generic x86_64 (64 bit gcc: 5.4.0)
Desktop: MATE 1.18.0 (Gtk 3.18.9-1ubuntu3.3)
Distro: Linux Mint 18.3 Sylvia
Machine: System: Dell (portable) product: Inspiron 5323
Mobo: Dell model: 06J1DG v: A00 Bios: Dell v: A13 date: 12/14/2012
CPU: Dual core Intel Core i3-3227U (-HT-MCP-) cache: 3072 KB
flags: (lm nx sse sse2 sse3 sse4_1 sse4_2 ssse3 vmx) bmips: 7582
clock speeds: max: 1900 MHz 1: 1895 MHz 2: 1895 MHz 3: 1895 MHz
4: 1895 MHz
Graphics: Card: Intel 3rd Gen Core processor Graphics Controller
bus-ID: 00:02.0
Display Server: X.Org 1.18.4 drivers: intel (unloaded: fbdev,vesa)
Resolution: 1366x768@59.93hz
GLX Renderer: Mesa DRI Intel Ivybridge Mobile
GLX Version: 3.0 Mesa 17.2.8 Direct Rendering: Yes
Audio: Card Intel 7 Series/C210 Series Family High Definition Audio Controller
driver: snd_hda_intel bus-ID: 00:1b.0
Sound: Advanced Linux Sound Architecture v: k4.13.0-32-generic
Network: Card: Intel Centrino Wireless-N 2230
driver: iwlwifi bus-ID: 01:00.0
IF: wlp1s0 state: up mac: <filter>
Drives: HDD Total Size: 500.1GB (18.5% used)
ID-1: /dev/sda model: WDC_WD5000LPVT size: 500.1GB
Partition: ID-1: / size: 455G used: 83G (20%) fs: ext4 dev: /dev/sda1
ID-2: swap-1 size: 4.15GB used: 0.00GB (0%) fs: swap dev: /dev/sda5
RAID: No RAID devices: /proc/mdstat, md_mod kernel module present
Sensors: System Temperatures: cpu: 52.0C mobo: 27.8C
Fan Speeds (in rpm): cpu: N/A
Info: Processes: 189 Uptime: 12:05 Memory: 1228.9/3804.1MB
Init: systemd runlevel: 5 Gcc sys: 5.4.0
Client: Shell (bash 4.3.481) inxi: 2.2.35
el pueblo unido jamás será vencido

User avatar
ClixTrix
Level 5
Level 5
Posts: 697
Joined: Wed Dec 09, 2015 11:40 am
Location: Columbus, Ohio, USA

Re: dmesg results

Post by ClixTrix » Sun Mar 04, 2018 1:39 pm

captcharis wrote:
Sun Mar 04, 2018 1:01 pm
Machine: System: Dell (portable) product: Inspiron 5323
Mobo: Dell model: 06J1DG v: A00 Bios: Dell v: A13 date: 12/14/2012
The current BIOS for your system is A18. You have A13. It's possible the cam problem is linked to a BIOS problem.

http://www.dell.com/support/home/us/en/ ... 23/drivers

I don't see the Ethernet listed as a Network Card on that list. My check of specs for the laptop does show a 10/100 Ethernet. So, disable of the NIC is the Ethernet port.

I would expect disable of the Cam to be designated as Video Camera in the BIOS.
Linux Mint 18.3 x64 Cinnamon Kernel 4.15.0-23-generic
Gigabyte GA-AB350M-D3H (F20) / Ryzen 5 1600 / Micron Ballistix Sport DDR4 2400 2x8GB / XFX HD5450-1GB
NVMe-SSD Samsung EVO 960 250GB / SATA-HDD WD1600BEKT 160GB / SATA-SSD Toshiba OCZ VX500 512GB

captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

Re: dmesg results

Post by captcharis » Mon Mar 05, 2018 3:41 am

Hello again Clix!!!

I downloaded the BIOS updates ( I really have not any idea that there are updates for BIOS also) , but is .exe,
I can't run it.
I have to tell you that my camera didn't work even before , I mean pre-Mint installation and every time I start up my Laptop I have the same msg in the star up screen.

[41563.026380] usb 1-1-port5: unable to enumerate USB device
[41566.806248] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[41567.658288] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[41568.510144] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[41569.362092] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[41569.362244] usb 1-1-port5: unable to enumerate USB device
[41573.142073] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[41573.998073] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[41574.850072] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[41575.702059] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad


Also in my BIOS I didn't find anything relative to camera :roll:

Thanks for your help my friend , something else , how did you learn all this ? I mean is this your job or what?
Can I learn all this , is there any on line tutorial?
Thanks again
el pueblo unido jamás será vencido

User avatar
catweazel
Level 14
Level 14
Posts: 5457
Joined: Fri Oct 12, 2012 9:44 pm
Location: Australian Antarctic Territory

Re: dmesg results

Post by catweazel » Mon Mar 05, 2018 3:45 am

captcharis wrote:
Mon Mar 05, 2018 3:41 am
I downloaded the BIOS updates ( I really have not any idea that there are updates for BIOS also) , but is .exe,
I can't run it.
Sure you can. https://community.spiceworks.com/how_to ... ing-ubuntu

Three simple steps.
A new scientific truth does not triumph by convincing its opponents and making them see the light, but rather because its opponents eventually die, and a new generation grows up that is familiar with it. - Max Planck

captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

Re: dmesg results

Post by captcharis » Mon Mar 05, 2018 5:00 am

That's why you are on Level 12 and I'm on Level 1 :D
anyway I will need a little further help
I don't know what to complete here
Screenshot at 2018-03-05 10-48-59.jpg
so I did this, I don't know if this is correct
Screenshot at 2018-03-05 10-49-24.jpg
and after all that what ?
in BIOS I found it very hard for me :mrgreen:
el pueblo unido jamás será vencido

captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

Re: dmesg results

Post by captcharis » Mon Mar 05, 2018 8:25 am

Dear gentlemen !!!!

Forget my previous, BIOS update is Done :P :lol: (Yeap I'm f**king happy, I did it) thanks to you and web!
Here it is

Machine: System: Dell (portable) product: Inspiron 5323
Mobo: Dell model: 06J1DG v: A00 Bios: Dell v: A18 date: 09/25/2013

But the problem with usb still exist

[ 399.018851] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[ 399.870349] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[ 400.721831] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[ 401.573465] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[ 401.573623] usb 1-1-port5: unable to enumerate USB device
[ 405.351311] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[ 406.202788] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[ 407.054419] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[ 407.905913] usb 1-1-port5: Cannot enable. Maybe the USB cable is bad?
[ 407.906072] usb 1-1-port5: unable to enumerate USB device
el pueblo unido jamás será vencido

User avatar
ClixTrix
Level 5
Level 5
Posts: 697
Joined: Wed Dec 09, 2015 11:40 am
Location: Columbus, Ohio, USA

Re: dmesg results

Post by ClixTrix » Mon Mar 05, 2018 9:37 am

Any chance the BIOS update added an option to disable the Cam?
Linux Mint 18.3 x64 Cinnamon Kernel 4.15.0-23-generic
Gigabyte GA-AB350M-D3H (F20) / Ryzen 5 1600 / Micron Ballistix Sport DDR4 2400 2x8GB / XFX HD5450-1GB
NVMe-SSD Samsung EVO 960 250GB / SATA-HDD WD1600BEKT 160GB / SATA-SSD Toshiba OCZ VX500 512GB

captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

Re: dmesg results

Post by captcharis » Mon Mar 05, 2018 10:35 am

Nothing my friend
As menu as concern remain the same
el pueblo unido jamás será vencido

User avatar
ClixTrix
Level 5
Level 5
Posts: 697
Joined: Wed Dec 09, 2015 11:40 am
Location: Columbus, Ohio, USA

Re: dmesg results

Post by ClixTrix » Mon Mar 05, 2018 10:51 am

Please run the following command from Terminal and post back the results (this produces a short list of USB devices). The prior list was cutoff at the top, and I just want to double-check what Linux sees.

Code: Select all

lsusb
Also, is there any ability in BIOS to disable USB hubs/ports?
Last edited by ClixTrix on Mon Mar 05, 2018 10:51 am, edited 1 time in total.
Linux Mint 18.3 x64 Cinnamon Kernel 4.15.0-23-generic
Gigabyte GA-AB350M-D3H (F20) / Ryzen 5 1600 / Micron Ballistix Sport DDR4 2400 2x8GB / XFX HD5450-1GB
NVMe-SSD Samsung EVO 960 250GB / SATA-HDD WD1600BEKT 160GB / SATA-SSD Toshiba OCZ VX500 512GB

User avatar
Flemur
Level 15
Level 15
Posts: 5659
Joined: Mon Aug 20, 2012 9:41 pm
Location: Potemkin Village

Re: dmesg results

Post by Flemur » Mon Mar 05, 2018 10:51 am

I'm getting those messages also.
viewtopic.php?f=49&t=264971
Purging the microcode package seems to have reduced them. The "cable" messages come and go.

It's been a kernel bug for years, perhaps because, as near as I can tell, the USB development for the linux kernel has been a "social justice" project for a long time.
Edit: the bug has been around since 2007:
https://bugs.launchpad.net/ubuntu/+sour ... +bug/88746


PS: a better title to your original post would assist in you getting answers. "dmesg results" could be about almost anything.
Please edit your original post title to include [SOLVED] if/when it is solved!
Your data and OS are backed up....right?
Mint 18.3 Xfce/fluxbox/pulse-less
Xubuntu 17.10/fluxbox/pulse-less

captcharis
Level 1
Level 1
Posts: 26
Joined: Fri Sep 01, 2017 9:11 am
Location: Greece

Re: dmesg results

Post by captcharis » Tue Mar 06, 2018 12:38 am

Good morning Guys
Here is usb list

Bus 002 Device 003: ID 8087:07da Intel Corp.
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. RTS5129 Card Reader Controller
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

In BIOS menu there are three options regarding USD
  • USB emulation - Enable
    USB Powershare - Enable
    USB Wake Support - Disable
I changed all of them to opposite option but problem remain!!

But if all this is a "bug" so that means that no any problem really exist correct?
PS: a better title to your original post would assist in you getting answers. "dmesg results" could be about almost anything.
Next time I would try to be more specific but my problem is that I don't really know what I have to deal with :roll:
Sorry for that and thanks one again for your help guys
el pueblo unido jamás será vencido

User avatar
ClixTrix
Level 5
Level 5
Posts: 697
Joined: Wed Dec 09, 2015 11:40 am
Location: Columbus, Ohio, USA

Re: dmesg results

Post by ClixTrix » Tue Mar 06, 2018 8:51 am

Well, here's my thinking and options. I'm assuming the cam is the problem as you stated it wasn't working prior to Linux. However, it could also be a motherboard USB hub problem or bad ribbon cable.

The power error is probably due to the dead cam, which might be causing a short or power-draw problem. I can only think of two possible options:

1) Disable hardware in BIOS. However, there doesn't appear to be any method to disable either the cam or the USB hubs/ports from BIOS.

2) Remove or Replace the defective Cam. I have located a procedure, but it isn't something I would recommend to a novice without the proper tools/skills. A local laptop repair shop would be a better choice.

https://www.youtube.com/watch?v=rwavFE9DvL0

As for the cost of the cam, it's not an expensive item.

https://www.ebay.com/itm/Dell-Inspiron- ... SwPe1UIgeI

If the dmesg errors aren't causing any real system problems, you could simply ignore them. I'm not sure if the other USB ports are working or not. That you would need to test.

If there is more to the problem, it might be possible to blacklist the cam or the hub.

I'm not sure if Flemur's suggestion is applicable due to the cam being a known hardware failure problem.
Linux Mint 18.3 x64 Cinnamon Kernel 4.15.0-23-generic
Gigabyte GA-AB350M-D3H (F20) / Ryzen 5 1600 / Micron Ballistix Sport DDR4 2400 2x8GB / XFX HD5450-1GB
NVMe-SSD Samsung EVO 960 250GB / SATA-HDD WD1600BEKT 160GB / SATA-SSD Toshiba OCZ VX500 512GB

Post Reply

Return to “Hardware Support”