smart check, explain me and if its bad how to fix it

[since2019]

Code: Select all

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   062    Pre-fail  Always       -       1
  2 Throughput_Performance  0x0005   100   100   040    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0007   230   230   033    Pre-fail  Always       -       1
  4 Start_Stop_Count        0x0012   094   094   000    Old_age   Always       -       10406
  5 Reallocated_Sector_Ct   0x0033   001   001   005    Pre-fail  Always   FAILING_NOW 0
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   040    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0012   038   038   000    Old_age   Always       -       27577
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   094   094   000    Old_age   Always       -       10368
191 G-Sense_Error_Rate      0x000a   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       175
193 Load_Cycle_Count        0x0012   073   073   000    Old_age   Always       -       276269
194 Temperature_Celsius     0x0002   114   114   000    Old_age   Always       -       48 (Min/Max 18/55)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       5275
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       10
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   253   000    Old_age   Always       -       0
223 Load_Retry_Count        0x000a   100   100   000    Old_age   Always       -       0

i know partition 1 is failing with "corrupt" files too. Says something like this:
(even with a clean install formated partition 1)

exception Emask 0x0 SAct 0x0 SErr 0/0 action 0x0
BMDMA stat 0x25
failed command: READ DMA
cmd
res
status { DRDY ERR }
error: { UNC }
_req_error: I/O error, dev sda, sector .... flags
error on swap-device

partition 2 with linux working fine, partition 3 with windows trial working fine.
whats is wrong with sda1 or disk something...

[JoeFootball]

i know partition 1 is failing with "corrupt" files too. Says something like this:
(even with a clean install formated partition 1)

If I had an older hard drive with a partition that continued to fail even after formatting it, I'd consider a new drive.

Regardless, this article details a decent list of S.M.A.R.T. attributes ...

https://en.wikipedia.org/wiki/S.M.A.R.T.

[rene]

To Joe, note that this was also already answered at viewtopic.php?p=2003257#p2003257 and including a possible try-around (which should however not even be attempted in this case; that drive is toast).

[JoeFootball]

... that drive is toast

As suspected.