Solved - No Sound - Dell Precision 5760

Questions about hardware, drivers and peripherals
Forum rules
Before you post read how to get help. Topics in this forum are automatically closed 6 months after creation.
Locked
alchez3
Level 1
Level 1
Posts: 5
Joined: Mon Sep 20, 2021 4:29 pm

Solved - No Sound - Dell Precision 5760

Post by alchez3 »

I have a Dell Precision 5760 with fresh install linux mint 20.2 running the 5.11 Kernal, as needed to resolve Nvidia card issue. I have followed several post regarding no sound with no success. Pulse Control shows "Dummy output" under output tab and "HDA Nvidia" under the config tab but profiles are all (unplugged) (unavailable). The video card is a Nvidia RTX A3000.

Thank you.
Last edited by LockBot on Wed Dec 28, 2022 7:16 am, edited 2 times in total.
Reason: Topic automatically closed 6 months after creation. New replies are no longer allowed.
Aztaroth
Level 5
Level 5
Posts: 769
Joined: Mon Jan 11, 2021 1:48 am

Re: No Sound - Dell Precision 5760

Post by Aztaroth »

Mint 20.2 Release Notes :
Sound and microphone issues

If you're facing issues with your microphone or your sound output, please install "pavucontrol".

This will add "PulseAudio Volume Control" to your menu. This application has more configuration options than the default volume control.
dual boot LMDE4 (mostly) + LM19.3 Cinnamon (sometimes)
alchez3
Level 1
Level 1
Posts: 5
Joined: Mon Sep 20, 2021 4:29 pm

Re: No Sound - Dell Precision 5760

Post by alchez3 »

alchez3 wrote: Mon Sep 20, 2021 4:58 pm I have followed several post regarding no sound with no success. Pulse Control shows "Dummy output" under output tab and "HDA Nvidia" under the config tab but profiles are all (unplugged) (unavailable).
Thanks for the reply, I have followed those procedures and am stuck with no audio.
Aztaroth
Level 5
Level 5
Posts: 769
Joined: Mon Jan 11, 2021 1:48 am

Re: No Sound - Dell Precision 5760

Post by Aztaroth »

Hello,
If the basics didn't work, some sysinfo will be necessary to try for a better help. Please post output of :

Code: Select all

inxi -Fxxxz
dual boot LMDE4 (mostly) + LM19.3 Cinnamon (sometimes)
alchez3
Level 1
Level 1
Posts: 5
Joined: Mon Sep 20, 2021 4:29 pm

Re: No Sound - Dell Precision 5760

Post by alchez3 »

Output as request. thank you.

I believe the issues is "Device-1: Intel vendor: Dell driver: sof-audio-pci bus ID: 0000:00:1f.3
chip ID: 8086:43c8" is not loading but I cannot figure out how to get it to load. Also below I have included a screenshot of PulseAduioControl.

Code: Select all

System:
  Kernel: 5.11.0-36-generic x86_64 bits: 64 compiler: N/A 
  Desktop: Cinnamon 5.0.5 wm: muffin 5.0.1 dm: LightDM 1.30.0 
  Distro: Linux Mint 20.2 Uma base: Ubuntu 20.04 focal 
Machine:
  Type: Laptop System: Dell product: Precision 5760 v: N/A serial: <filter> 
  Chassis: type: 10 serial: <filter> 
  Mobo: Dell model: 0T7J1J v: A00 serial: <filter> UEFI: Dell v: 1.4.1 
  date: 09/08/2021 
Battery:
  ID-1: BAT0 charge: 2.7 Wh condition: 91.2/95.1 Wh (96%) volts: 11.8/11.4 
  model: SMP DELL 01RR3YM type: Li-poly serial: <filter> status: Charging 
CPU:
  Topology: 8-Core model: 11th Gen Intel Core i7-11850H bits: 64 
  type: MT MCP arch: N/A L2 cache: 24.0 MiB 
  flags: avx avx2 lm nx pae sse sse2 sse3 sse4_1 sse4_2 ssse3 vmx 
  bogomips: 79872 
  Speed: 976 MHz min/max: 800/4800 MHz Core speeds (MHz): 1: 1535 2: 800 
  3: 4800 4: 1441 5: 800 6: 801 7: 800 8: 788 9: 945 10: 2898 11: 2078 
  12: 800 13: 1924 14: 1093 15: 930 16: 889 
Graphics:
  Device-1: Intel vendor: Dell driver: i915 v: kernel bus ID: 0000:00:02.0 
  chip ID: 8086:9a60 
  Device-2: NVIDIA vendor: Dell driver: nvidia v: 470.63.01 
  bus ID: 0000:01:00.0 chip ID: 10de:24b8 
  Display: x11 server: X.Org 1.20.11 driver: modesetting,nvidia 
  unloaded: fbdev,nouveau,vesa resolution: 1920x1200~60Hz 
  OpenGL: renderer: Mesa Intel UHD Graphics (TGL GT1) v: 4.6 Mesa 21.0.3 
  direct render: Yes 
Audio:
  Device-1: Intel vendor: Dell driver: sof-audio-pci bus ID: 0000:00:1f.3 
  chip ID: 8086:43c8 
  Device-2: NVIDIA vendor: Dell driver: snd_hda_intel v: kernel 
  bus ID: 0000:01:00.1 chip ID: 10de:228b 
  Sound Server: ALSA v: k5.11.0-36-generic 
Network:
  Device-1: Intel driver: iwlwifi v: kernel port: 4000 bus ID: 0000:00:14.3 
  chip ID: 8086:43f0 
  IF: wlp0s20f3 state: up mac: <filter> 
Drives:
  Local Storage: total: 476.94 GiB used: 29.50 GiB (6.2%) 
  ID-1: /dev/nvme0n1 vendor: SK Hynix model: PC711 NVMe 512GB 
  size: 476.94 GiB speed: 31.6 Gb/s lanes: 4 serial: <filter> rev: 41001131 
  scheme: GPT 
RAID:
  Hardware-1: Intel Volume Management Device NVMe RAID Controller 
  driver: vmd v: 0.6 port: 4000 bus ID: 0000:00:0e.0 chip ID: 8086.9a0b 
  rev: N/A 
Partition:
  ID-1: / size: 466.30 GiB used: 14.49 GiB (3.1%) fs: ext4 dev: /dev/dm-1 
  ID-2: /boot size: 704.5 MiB used: 517.2 MiB (73.4%) fs: ext4 
  dev: /dev/nvme0n1p2 
  ID-3: swap-1 size: 980.0 MiB used: 0 KiB (0.0%) fs: swap dev: /dev/dm-2 
Sensors:
  System Temperatures: cpu: 26.0 C mobo: N/A 
  Fan Speeds (RPM): N/A 
Info:
  Processes: 406 Uptime: 3m Memory: 31.10 GiB used: 1.63 GiB (5.2%) 
  Init: systemd v: 245 runlevel: 5 Compilers: gcc: 9.3.0 alt: 9 Shell: bash 
  v: 5.0.17 running in: gnome-terminal inxi: 3.0.38 
2021-09-26_14-41.png
User avatar
MrEen
Level 23
Level 23
Posts: 18345
Joined: Mon Jun 12, 2017 8:39 pm

Re: No Sound - Dell Precision 5760

Post by MrEen »

Hi alchez3, and welcome to the forum.

Let's get a look at your sound setup with this command:

Code: Select all

curl https://gitlab.freedesktop.org/pulseaudio/pulseaudio/raw/master/src/utils/pa-info?inline=false | bash | nc termbin.com 9999
The last line of output will have a URL pointing to the info. Pasting that URL is all I need.
alchez3
Level 1
Level 1
Posts: 5
Joined: Mon Sep 20, 2021 4:29 pm

Re: No Sound - Dell Precision 5760

Post by alchez3 »

Thanks for the help. I have attached the output file of the script here as well.

Code: Select all

> pulseaudio_ps_do
alfred      1651  1.8  0.0 1932380 19604 ?       S<sl Sep26  25:32 /usr/bin/pulseaudio --daemonize=no --log-target=journal
alfred     40981  0.0  0.0   3312   668 pts/0    S+   13:08   0:00 grep pulseaudio
________________
> which pulseaudio
/usr/bin/pulseaudio
________________
> pidof pulseaudio
1651
________________
> pulseaudio --version
pulseaudio 13.99.1
________________
> pactl info
Server String: /run/user/1000/pulse/native
Library Protocol Version: 33
Server Protocol Version: 33
Is Local: yes
Client Index: 5059
Tile Size: 65472
User Name: alfred
Host Name: alfred-Precision-5760
Server Name: pulseaudio
Server Version: 13.99.1
Default Sample Specification: s16le 2ch 44100Hz
Default Channel Map: front-left,front-right
Default Sink: auto_null
Default Source: auto_null.monitor
Cookie: 65c2:a4fe
________________
> pactl list
Module #0
	Name: module-device-restore
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Automatically restore the volume/mute state of devices"
		module.version = "13.99.1"

Module #1
	Name: module-stream-restore
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Automatically restore the volume/mute/device state of streams"
		module.version = "13.99.1"

Module #2
	Name: module-card-restore
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Automatically restore profile of cards"
		module.version = "13.99.1"

Module #3
	Name: module-augment-properties
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Augment the property sets of streams with additional static information"
		module.version = "13.99.1"

Module #4
	Name: module-switch-on-port-available
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "David Henningsson"
		module.description = "Switches ports and profiles when devices are plugged/unplugged"
		module.version = "13.99.1"

Module #5
	Name: module-switch-on-connect
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Michael Terry"
		module.description = "When a sink/source is added, switch to it or conditionally switch to it"
		module.version = "13.99.1"

Module #6
	Name: module-udev-detect
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Detect available audio hardware and load matching drivers"
		module.version = "13.99.1"

Module #7
	Name: module-alsa-card
	Argument: device_id="0" name="pci-0000_01_00.1" card_name="alsa_card.pci-0000_01_00.1" namereg_fail=false tsched=yes fixed_latency_range=no ignore_dB=no deferred_volume=yes use_ucm=yes avoid_resampling=no card_properties="module-udev-detect.discovered=1"
	Usage counter: 0
	Properties:
		module.author = "Lennart Poettering"
		module.description = "ALSA Card"
		module.version = "13.99.1"

Module #8
	Name: module-native-protocol-unix
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Native protocol (UNIX sockets)"
		module.version = "13.99.1"

Module #9
	Name: module-default-device-restore
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Automatically restore the default sink and source"
		module.version = "13.99.1"

Module #10
	Name: module-always-sink
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Colin Guthrie"
		module.description = "Always keeps at least one sink loaded even if it's a null one"
		module.version = "13.99.1"

Module #12
	Name: module-intended-roles
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Automatically set device of streams based on intended roles of devices"
		module.version = "13.99.1"

Module #13
	Name: module-suspend-on-idle
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "When a sink/source is idle for too long, suspend it"
		module.version = "13.99.1"

Module #14
	Name: module-console-kit
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Create a client for each ConsoleKit session of this user"
		module.version = "13.99.1"

Module #15
	Name: module-systemd-login
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Create a client for each login session of this user"
		module.version = "13.99.1"

Module #16
	Name: module-position-event-sounds
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Position event sounds between L and R depending on the position on screen of the widget triggering them."
		module.version = "13.99.1"

Module #17
	Name: module-role-cork
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Mute & cork streams with certain roles while others exist"
		module.version = "13.99.1"

Module #18
	Name: module-snap-policy
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Canonical Ltd"
		module.description = "Ubuntu Snap policy management"
		module.version = "13.99.1"

Module #19
	Name: module-filter-heuristics
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Colin Guthrie"
		module.description = "Detect when various filters are desirable"
		module.version = "13.99.1"

Module #20
	Name: module-filter-apply
	Argument: 
	Usage counter: n/a
	Properties:
		module.author = "Colin Guthrie"
		module.description = "Load filter sinks automatically when needed"
		module.version = "13.99.1"

Module #21
	Name: module-x11-publish
	Argument: display=:0 xauthority=/home/alfred/.Xauthority
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "X11 credential publisher"
		module.version = "13.99.1"

Module #22
	Name: module-x11-cork-request
	Argument: display=:0 xauthority=/home/alfred/.Xauthority
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Synthesize X11 media key events when cork/uncork is requested"
		module.version = "13.99.1"

Module #23
	Name: module-x11-xsmp
	Argument: display=:0 xauthority=/home/alfred/.Xauthority session_manager=local/alfred-Precision-5760:@/tmp/.ICE-unix/1662,unix/alfred-Precision-5760:/tmp/.ICE-unix/1662
	Usage counter: n/a
	Properties:
		module.author = "Lennart Poettering"
		module.description = "X11 session management"
		module.version = "13.99.1"

Module #25
	Name: module-null-sink
	Argument: sink_name=auto_null sink_properties='device.description="Dummy Output"'
	Usage counter: 3
	Properties:
		module.author = "Lennart Poettering"
		module.description = "Clocked NULL sink"
		module.version = "13.99.1"

Sink #4
	State: RUNNING
	Name: auto_null
	Description: Dummy Output
	Driver: module-null-sink.c
	Sample Specification: s16le 2ch 44100Hz
	Channel Map: front-left,front-right
	Owner Module: 25
	Mute: no
	Volume: front-left: 65536 / 100% / 0.00 dB,   front-right: 65536 / 100% / 0.00 dB
	        balance 0.00
	Base Volume: 65536 / 100% / 0.00 dB
	Monitor Source: auto_null.monitor
	Latency: 78 usec, configured 500 usec
	Flags: DECIBEL_VOLUME LATENCY SET_FORMATS 
	Properties:
		device.description = "Dummy Output"
		device.class = "abstract"
		device.icon_name = "audio-card"
	Formats:
		pcm

Source #4
	State: IDLE
	Name: auto_null.monitor
	Description: Monitor of Dummy Output
	Driver: module-null-sink.c
	Sample Specification: s16le 2ch 44100Hz
	Channel Map: front-left,front-right
	Owner Module: 25
	Mute: no
	Volume: front-left: 65536 / 100% / 0.00 dB,   front-right: 65536 / 100% / 0.00 dB
	        balance 0.00
	Base Volume: 65536 / 100% / 0.00 dB
	Monitor of Sink: auto_null
	Latency: 0 usec, configured 2000000 usec
	Flags: DECIBEL_VOLUME LATENCY 
	Properties:
		device.description = "Monitor of Dummy Output"
		device.class = "monitor"
		device.icon_name = "audio-input-microphone"
	Formats:
		pcm

Sink Input #11
	Driver: protocol-native.c
	Owner Module: 8
	Client: 5038
	Sink: 4
	Sample Specification: s16le 1ch 44100Hz
	Channel Map: mono
	Format: pcm, format.sample_format = "\"s16le\""  format.rate = "44100"  format.channels = "1"  format.channel_map = "\"mono\""
	Corked: no
	Mute: no
	Volume: mono: 60436 /  92% / -2.11 dB
	        balance 0.00
	Buffer Latency: 0 usec
	Sink Latency: 474 usec
	Resample method: copy
	Properties:
		media.name = "playback"
		application.name = "speech-dispatcher-espeak-ng"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.process.id = "38807"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "sd_espeak-ng"
		application.language = "C"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"
		module-stream-restore.id = "sink-input-by-application-name:speech-dispatcher-espeak-ng"

Sink Input #12
	Driver: protocol-native.c
	Owner Module: 8
	Client: 5039
	Sink: 4
	Sample Specification: s16le 1ch 44100Hz
	Channel Map: mono
	Format: pcm, format.sample_format = "\"s16le\""  format.rate = "44100"  format.channels = "1"  format.channel_map = "\"mono\""
	Corked: no
	Mute: no
	Volume: mono: 66479 / 101% / 0.37 dB
	        balance 0.00
	Buffer Latency: 0 usec
	Sink Latency: 462 usec
	Resample method: copy
	Properties:
		media.name = "playback"
		application.name = "speech-dispatcher-dummy"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.process.id = "38813"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "sd_dummy"
		application.language = "C"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"
		module-stream-restore.id = "sink-input-by-application-name:speech-dispatcher-dummy"

Sink Input #13
	Driver: protocol-native.c
	Owner Module: 8
	Client: 5040
	Sink: 4
	Sample Specification: s16le 1ch 44100Hz
	Channel Map: mono
	Format: pcm, format.sample_format = "\"s16le\""  format.rate = "44100"  format.channels = "1"  format.channel_map = "\"mono\""
	Corked: no
	Mute: no
	Volume: mono: 65536 / 100% / 0.00 dB
	        balance 0.00
	Buffer Latency: 0 usec
	Sink Latency: 452 usec
	Resample method: copy
	Properties:
		media.name = "playback"
		application.name = "speech-dispatcher-generic"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.process.id = "38816"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "sd_generic"
		application.language = "C"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"
		module-stream-restore.id = "sink-input-by-application-name:speech-dispatcher-generic"

Client #0
	Driver: module-systemd-login.c
	Owner Module: 15
	Properties:
		application.name = "Login Session c2"
		systemd-login.session = "c2"

Client #2
	Driver: protocol-native.c
	Owner Module: 8
	Properties:
		application.name = "Cinnamon Volume Control Media Keys"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.id = "org.gnome.VolumeControl"
		application.icon_name = "multimedia-volume-control"
		application.version = "5.0.0"
		application.process.id = "1817"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "csd-media-keys"
		application.language = "en_US.UTF-8"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"

Client #5
	Driver: module-x11-xsmp.c
	Owner Module: 23
	Properties:
		application.name = "XSMP Session on cinnamon-session as 10d07680f5f1bae1163268062423508500000016620056"
		xsmp.vendor = "cinnamon-session"
		xsmp.client.id = "10d07680f5f1bae1163268062423508500000016620056"

Client #6
	Driver: protocol-native.c
	Owner Module: 8
	Properties:
		application.name = "Cinnamon Volume Control"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.id = "org.gnome.VolumeControl"
		application.icon_name = "multimedia-volume-control"
		application.version = "5.0.0"
		application.process.id = "1927"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "cinnamon"
		application.language = "en_US.UTF-8"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"

Client #7
	Driver: protocol-native.c
	Owner Module: 8
	Properties:
		application.name = "libcanberra"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.version = "0.30"
		application.id = "org.freedesktop.libcanberra"
		application.process.id = "1777"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "csd-sound"
		application.language = "en_US.UTF-8"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"

Client #5038
	Driver: protocol-native.c
	Owner Module: 8
	Properties:
		application.name = "speech-dispatcher-espeak-ng"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.process.id = "38807"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "sd_espeak-ng"
		application.language = "C"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"

Client #5039
	Driver: protocol-native.c
	Owner Module: 8
	Properties:
		application.name = "speech-dispatcher-dummy"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.process.id = "38813"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "sd_dummy"
		application.language = "C"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"

Client #5040
	Driver: protocol-native.c
	Owner Module: 8
	Properties:
		application.name = "speech-dispatcher-generic"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.process.id = "38816"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "sd_generic"
		application.language = "C"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"

Client #5060
	Driver: protocol-native.c
	Owner Module: 8
	Properties:
		application.name = "pactl"
		native-protocol.peer = "UNIX socket client"
		native-protocol.version = "33"
		application.process.id = "40986"
		application.process.user = "alfred"
		application.process.host = "alfred-Precision-5760"
		application.process.binary = "pactl"
		application.language = "C"
		window.x11.display = ":0"
		application.process.machine_id = "dafd9a61376b4676aa8b190bc1ed4b43"
		application.process.session_id = "c2"

Card #0
	Name: alsa_card.pci-0000_01_00.1
	Driver: module-alsa-card.c
	Owner Module: 7
	Properties:
		alsa.card = "0"
		alsa.card_name = "HDA NVidia"
		alsa.long_card_name = "HDA NVidia at 0xac000000 irq 17"
		alsa.driver_name = "snd_hda_intel"
		device.bus_path = "pci-0000:01:00.1"
		sysfs.path = "/devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card0"
		device.bus = "pci"
		device.vendor.id = "10de"
		device.vendor.name = "NVIDIA Corporation"
		device.product.id = "228b"
		device.string = "0"
		device.description = "HDA NVidia"
		module-udev-detect.discovered = "1"
		device.icon_name = "audio-card-pci"
	Profiles:
		output:hdmi-stereo: Digital Stereo (HDMI) Output (sinks: 1, sources: 0, priority: 5900, available: no)
		output:hdmi-surround: Digital Surround 5.1 (HDMI) Output (sinks: 1, sources: 0, priority: 800, available: no)
		output:hdmi-surround71: Digital Surround 7.1 (HDMI) Output (sinks: 1, sources: 0, priority: 800, available: no)
		output:hdmi-stereo-extra1: Digital Stereo (HDMI 2) Output (sinks: 1, sources: 0, priority: 5700, available: no)
		output:hdmi-surround-extra1: Digital Surround 5.1 (HDMI 2) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-surround71-extra1: Digital Surround 7.1 (HDMI 2) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-stereo-extra2: Digital Stereo (HDMI 3) Output (sinks: 1, sources: 0, priority: 5700, available: no)
		output:hdmi-surround-extra2: Digital Surround 5.1 (HDMI 3) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-surround71-extra2: Digital Surround 7.1 (HDMI 3) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-stereo-extra3: Digital Stereo (HDMI 4) Output (sinks: 1, sources: 0, priority: 5700, available: no)
		output:hdmi-surround-extra3: Digital Surround 5.1 (HDMI 4) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-surround71-extra3: Digital Surround 7.1 (HDMI 4) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-stereo-extra4: Digital Stereo (HDMI 5) Output (sinks: 1, sources: 0, priority: 5700, available: no)
		output:hdmi-surround-extra4: Digital Surround 5.1 (HDMI 5) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-surround71-extra4: Digital Surround 7.1 (HDMI 5) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-stereo-extra5: Digital Stereo (HDMI 6) Output (sinks: 1, sources: 0, priority: 5700, available: no)
		output:hdmi-surround-extra5: Digital Surround 5.1 (HDMI 6) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-surround71-extra5: Digital Surround 7.1 (HDMI 6) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-stereo-extra6: Digital Stereo (HDMI 7) Output (sinks: 1, sources: 0, priority: 5700, available: no)
		output:hdmi-surround-extra6: Digital Surround 5.1 (HDMI 7) Output (sinks: 1, sources: 0, priority: 600, available: no)
		output:hdmi-surround71-extra6: Digital Surround 7.1 (HDMI 7) Output (sinks: 1, sources: 0, priority: 600, available: no)
		off: Off (sinks: 0, sources: 0, priority: 0, available: yes)
	Active Profile: off
	Ports:
		hdmi-output-0: HDMI / DisplayPort (priority: 5900, latency offset: 0 usec, not available)
			Properties:
				device.icon_name = "video-display"
			Part of profile(s): output:hdmi-stereo, output:hdmi-surround, output:hdmi-surround71
		hdmi-output-1: HDMI / DisplayPort 2 (priority: 5800, latency offset: 0 usec, not available)
			Properties:
				device.icon_name = "video-display"
			Part of profile(s): output:hdmi-stereo-extra1, output:hdmi-surround-extra1, output:hdmi-surround71-extra1
		hdmi-output-2: HDMI / DisplayPort 3 (priority: 5700, latency offset: 0 usec, not available)
			Properties:
				device.icon_name = "video-display"
			Part of profile(s): output:hdmi-stereo-extra2, output:hdmi-surround-extra2, output:hdmi-surround71-extra2
		hdmi-output-3: HDMI / DisplayPort 4 (priority: 5600, latency offset: 0 usec, not available)
			Properties:
				device.icon_name = "video-display"
			Part of profile(s): output:hdmi-stereo-extra3, output:hdmi-surround-extra3, output:hdmi-surround71-extra3
		hdmi-output-4: HDMI / DisplayPort 5 (priority: 5500, latency offset: 0 usec, not available)
			Properties:
				device.icon_name = "video-display"
			Part of profile(s): output:hdmi-stereo-extra4, output:hdmi-surround-extra4, output:hdmi-surround71-extra4
		hdmi-output-5: HDMI / DisplayPort 6 (priority: 5400, latency offset: 0 usec, not available)
			Properties:
				device.icon_name = "video-display"
			Part of profile(s): output:hdmi-stereo-extra5, output:hdmi-surround-extra5, output:hdmi-surround71-extra5
		hdmi-output-6: HDMI / DisplayPort 7 (priority: 5300, latency offset: 0 usec, not available)
			Properties:
				device.icon_name = "video-display"
			Part of profile(s): output:hdmi-stereo-extra6, output:hdmi-surround-extra6, output:hdmi-surround71-extra6
________________
> cat /etc/pulse/daemon.conf
# This file is part of PulseAudio.
#


; daemonize = no
; fail = yes
; allow-module-loading = yes
; allow-exit = yes
; use-pid-file = yes
; system-instance = no
; local-server-type = user
; enable-shm = yes
; enable-memfd = yes
; shm-size-bytes = 0 # setting this 0 will use the system-default, usually 64 MiB
; lock-memory = no
; cpu-limit = no

; high-priority = yes
; nice-level = -11

; realtime-scheduling = yes
; realtime-priority = 5

; exit-idle-time = 20
; scache-idle-time = 20

; dl-search-path = (depends on architecture)

; load-default-script-file = yes
; default-script-file = /etc/pulse/default.pa

; log-target = auto
; log-level = notice
; log-meta = no
; log-time = no
; log-backtrace = 0

; resample-method = speex-float-1
; avoid-resampling = false
; enable-remixing = yes
; remixing-use-all-sink-channels = yes
; remixing-produce-lfe = no
; remixing-consume-lfe = no
; lfe-crossover-freq = 0

; flat-volumes = no

; rescue-streams = yes

; rlimit-fsize = -1
; rlimit-data = -1
; rlimit-stack = -1
; rlimit-core = -1
; rlimit-as = -1
; rlimit-rss = -1
; rlimit-nproc = -1
; rlimit-nofile = 256
; rlimit-memlock = -1
; rlimit-locks = -1
; rlimit-sigpending = -1
; rlimit-msgqueue = -1
; rlimit-nice = 31
; rlimit-rtprio = 9
; rlimit-rttime = 200000

; default-sample-format = s16le
; default-sample-rate = 44100
; alternate-sample-rate = 48000
; default-sample-channels = 2
; default-channel-map = front-left,front-right

; default-fragments = 4
; default-fragment-size-msec = 25

; enable-deferred-volume = yes
deferred-volume-safety-margin-usec = 1
; deferred-volume-extra-delay-usec = 0
________________
> cat /etc/pulse/client.conf
# This file is part of PulseAudio.
#


; default-sink =
; default-source =
; default-server =
; default-dbus-server =

; autospawn = yes
; daemon-binary = /usr/bin/pulseaudio
; extra-arguments = --log-target=syslog

; cookie-file =

; enable-shm = yes
; shm-size-bytes = 0 # setting this 0 will use the system-default, usually 64 MiB

; auto-connect-localhost = no
; auto-connect-display = no
________________
> cat /etc/pulse/default.pa
#!/usr/bin/pulseaudio -nF
#
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify it
# under the terms of the GNU Lesser General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, see <http://www.gnu.org/licenses/>.

# This startup script is used only if PulseAudio is started per-user
# (i.e. not in system mode)

.fail

### Automatically restore the volume of streams and devices
load-module module-device-restore
load-module module-stream-restore
load-module module-card-restore

### Automatically augment property information from .desktop files
### stored in /usr/share/application
load-module module-augment-properties

### Should be after module-*-restore but before module-*-detect
load-module module-switch-on-port-available

### Use hot-plugged devices like Bluetooth or USB automatically (LP: #1702794)
.ifexists module-switch-on-connect.so
load-module module-switch-on-connect
.endif

### Load audio drivers statically
### (it's probably better to not load these drivers manually, but instead
### use module-udev-detect -- see below -- for doing this automatically)
#load-module module-alsa-sink
#load-module module-alsa-source device=hw:1,0
#load-module module-oss device="/dev/dsp" sink_name=output source_name=input
#load-module module-oss-mmap device="/dev/dsp" sink_name=output source_name=input
#load-module module-null-sink
#load-module module-pipe-sink

### Automatically load driver modules depending on the hardware available
.ifexists module-udev-detect.so
load-module module-udev-detect
.else
### Use the static hardware detection module (for systems that lack udev support)
load-module module-detect
.endif

### Automatically connect sink and source if JACK server is present
.ifexists module-jackdbus-detect.so
.nofail
load-module module-jackdbus-detect channels=2
.fail
.endif

### Automatically load driver modules for Bluetooth hardware
.ifexists module-bluetooth-policy.so
load-module module-bluetooth-policy
.endif

.ifexists module-bluetooth-discover.so
load-module module-bluetooth-discover
.endif

### Load several protocols
.ifexists module-esound-protocol-unix.so
load-module module-esound-protocol-unix
.endif
load-module module-native-protocol-unix

### Network access (may be configured with paprefs, so leave this commented
### here if you plan to use paprefs)
#load-module module-esound-protocol-tcp
#load-module module-native-protocol-tcp
#load-module module-zeroconf-publish

### Load the RTP receiver module (also configured via paprefs, see above)
#load-module module-rtp-recv

### Load the RTP sender module (also configured via paprefs, see above)
#load-module module-null-sink sink_name=rtp format=s16be channels=2 rate=44100 sink_properties="device.description='RTP Multicast Sink'"
#load-module module-rtp-send source=rtp.monitor

### Load additional modules from GSettings. This can be configured with the paprefs tool.
### Please keep in mind that the modules configured by paprefs might conflict with manually
### loaded modules.
.ifexists module-gsettings.so
.nofail
load-module module-gsettings
.fail
.endif


### Automatically restore the default sink/source when changed by the user
### during runtime
### NOTE: This should be loaded as early as possible so that subsequent modules
### that look up the default sink/source get the right value
load-module module-default-device-restore

### Make sure we always have a sink around, even if it is a null sink.
load-module module-always-sink

### Honour intended role device property
load-module module-intended-roles

### Automatically suspend sinks/sources that become idle for too long
load-module module-suspend-on-idle

### If autoexit on idle is enabled we want to make sure we only quit
### when no local session needs us anymore.
.ifexists module-console-kit.so
load-module module-console-kit
.endif
.ifexists module-systemd-login.so
load-module module-systemd-login
.endif

### Enable positioned event sounds
load-module module-position-event-sounds

### Cork music/video streams when a phone stream is active
load-module module-role-cork

### Block audio recording for snap confined packages unless they have
### the "pulseaudio" or "audio-record" interfaces plugged.
.ifexists module-snap-policy.so
load-module module-snap-policy
.endif

### Modules to allow autoloading of filters (such as echo cancellation)
### on demand. module-filter-heuristics tries to determine what filters
### make sense, and module-filter-apply does the heavy-lifting of
### loading modules and rerouting streams.
load-module module-filter-heuristics
load-module module-filter-apply

### Make some devices default
#set-default-sink output
#set-default-source input
________________
> cat /etc/pulse/system.pa
#!/usr/bin/pulseaudio -nF
#
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify it
# under the terms of the GNU Lesser General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, see <http://www.gnu.org/licenses/>.

# This startup script is used only if PulseAudio is started in system
# mode.

### Automatically restore the volume of streams and devices
load-module module-device-restore
load-module module-stream-restore
load-module module-card-restore

### Automatically load driver modules depending on the hardware available
.ifexists module-udev-detect.so
load-module module-udev-detect
.else
### Use the static hardware detection module (for systems that lack udev/hal support)
load-module module-detect
.endif

### Load several protocols
.ifexists module-esound-protocol-unix.so
load-module module-esound-protocol-unix
.endif
load-module module-native-protocol-unix

### Automatically restore the default sink/source when changed by the user
### during runtime
### NOTE: This should be loaded as early as possible so that subsequent modules
### that look up the default sink/source get the right value
load-module module-default-device-restore

### Make sure we always have a sink around, even if it is a null sink.
load-module module-always-sink

### Automatically suspend sinks/sources that become idle for too long
load-module module-suspend-on-idle

### Enable positioned event sounds
load-module module-position-event-sounds
________________
> ls -alt /dev/snd/*
crw-rw----+ 1 root audio 116,  8 Sep 26 15:51 /dev/snd/pcmC0D12p
crw-rw----+ 1 root audio 116,  7 Sep 26 15:51 /dev/snd/pcmC0D11p
crw-rw----+ 1 root audio 116,  6 Sep 26 15:51 /dev/snd/pcmC0D10p
crw-rw----+ 1 root audio 116,  5 Sep 26 15:51 /dev/snd/pcmC0D9p
crw-rw----+ 1 root audio 116,  4 Sep 26 15:51 /dev/snd/pcmC0D8p
crw-rw----+ 1 root audio 116,  3 Sep 26 15:51 /dev/snd/pcmC0D7p
crw-rw----+ 1 root audio 116,  2 Sep 26 15:51 /dev/snd/pcmC0D3p
crw-rw----+ 1 root audio 116, 10 Sep 26 14:23 /dev/snd/controlC0
crw-rw----+ 1 root audio 116,  9 Sep 26 14:23 /dev/snd/hwC0D0
crw-rw----+ 1 root audio 116,  1 Sep 26 14:23 /dev/snd/seq
crw-rw----+ 1 root audio 116, 33 Sep 26 14:23 /dev/snd/timer

/dev/snd/by-path:
total 0
drwxr-xr-x 2 root root  60 Sep 26 14:23 .
drwxr-xr-x 3 root root 280 Sep 26 14:23 ..
lrwxrwxrwx 1 root root  12 Sep 26 14:23 pci-0000:01:00.1 -> ../controlC0
________________
> lsof /dev/snd/*
COMMAND    PID   USER   FD   TYPE DEVICE SIZE/OFF NODE NAME
pulseaudi 1651 alfred   18u   CHR 116,10      0t0  635 /dev/snd/controlC0
________________
> jacks_do
card=0
numid=25,iface=CARD,name='HDMI/DP,pcm=10 Jack'
  ; type=BOOLEAN,access=r-------,values=1
  : values=off
numid=31,iface=CARD,name='HDMI/DP,pcm=11 Jack'
  ; type=BOOLEAN,access=r-------,values=1
  : values=off
numid=37,iface=CARD,name='HDMI/DP,pcm=12 Jack'
  ; type=BOOLEAN,access=r-------,values=1
  : values=off
numid=1,iface=CARD,name='HDMI/DP,pcm=3 Jack'
  ; type=BOOLEAN,access=r-------,values=1
  : values=off
numid=7,iface=CARD,name='HDMI/DP,pcm=7 Jack'
  ; type=BOOLEAN,access=r-------,values=1
  : values=off
numid=13,iface=CARD,name='HDMI/DP,pcm=8 Jack'
  ; type=BOOLEAN,access=r-------,values=1
  : values=off
numid=19,iface=CARD,name='HDMI/DP,pcm=9 Jack'
  ; type=BOOLEAN,access=r-------,values=1
  : values=off
________________
> aplay -L
default
    Playback/recording through the PulseAudio sound server
surround21
    2.1 Surround output to Front and Subwoofer speakers
surround40
    4.0 Surround output to Front and Rear speakers
surround41
    4.1 Surround output to Front, Rear and Subwoofer speakers
surround50
    5.0 Surround output to Front, Center and Rear speakers
surround51
    5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71
    7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
null
    Discard all samples (playback) or generate zero samples (capture)
samplerate
    Rate Converter Plugin Using Samplerate Library
speexrate
    Rate Converter Plugin Using Speex Resampler
jack
    JACK Audio Connection Kit
oss
    Open Sound System
pulse
    PulseAudio Sound Server
upmix
    Plugin for channel upmix (4,6,8)
vdownmix
    Plugin for channel downmix (stereo) with a simple spacialization
hdmi:CARD=NVidia,DEV=0
    HDA NVidia, HDMI 0
    HDMI Audio Output
hdmi:CARD=NVidia,DEV=1
    HDA NVidia, HDMI 1
    HDMI Audio Output
hdmi:CARD=NVidia,DEV=2
    HDA NVidia, HDMI 2
    HDMI Audio Output
hdmi:CARD=NVidia,DEV=3
    HDA NVidia, HDMI 3
    HDMI Audio Output
hdmi:CARD=NVidia,DEV=4
    HDA NVidia, HDMI 4
    HDMI Audio Output
hdmi:CARD=NVidia,DEV=5
    HDA NVidia, HDMI 5
    HDMI Audio Output
hdmi:CARD=NVidia,DEV=6
    HDA NVidia, HDMI 6
    HDMI Audio Output
dmix:CARD=NVidia,DEV=3
    HDA NVidia, HDMI 0
    Direct sample mixing device
dmix:CARD=NVidia,DEV=7
    HDA NVidia, HDMI 1
    Direct sample mixing device
dmix:CARD=NVidia,DEV=8
    HDA NVidia, HDMI 2
    Direct sample mixing device
dmix:CARD=NVidia,DEV=9
    HDA NVidia, HDMI 3
    Direct sample mixing device
dmix:CARD=NVidia,DEV=10
    HDA NVidia, HDMI 4
    Direct sample mixing device
dmix:CARD=NVidia,DEV=11
    HDA NVidia, HDMI 5
    Direct sample mixing device
dmix:CARD=NVidia,DEV=12
    HDA NVidia, HDMI 6
    Direct sample mixing device
dsnoop:CARD=NVidia,DEV=3
    HDA NVidia, HDMI 0
    Direct sample snooping device
dsnoop:CARD=NVidia,DEV=7
    HDA NVidia, HDMI 1
    Direct sample snooping device
dsnoop:CARD=NVidia,DEV=8
    HDA NVidia, HDMI 2
    Direct sample snooping device
dsnoop:CARD=NVidia,DEV=9
    HDA NVidia, HDMI 3
    Direct sample snooping device
dsnoop:CARD=NVidia,DEV=10
    HDA NVidia, HDMI 4
    Direct sample snooping device
dsnoop:CARD=NVidia,DEV=11
    HDA NVidia, HDMI 5
    Direct sample snooping device
dsnoop:CARD=NVidia,DEV=12
    HDA NVidia, HDMI 6
    Direct sample snooping device
hw:CARD=NVidia,DEV=3
    HDA NVidia, HDMI 0
    Direct hardware device without any conversions
hw:CARD=NVidia,DEV=7
    HDA NVidia, HDMI 1
    Direct hardware device without any conversions
hw:CARD=NVidia,DEV=8
    HDA NVidia, HDMI 2
    Direct hardware device without any conversions
hw:CARD=NVidia,DEV=9
    HDA NVidia, HDMI 3
    Direct hardware device without any conversions
hw:CARD=NVidia,DEV=10
    HDA NVidia, HDMI 4
    Direct hardware device without any conversions
hw:CARD=NVidia,DEV=11
    HDA NVidia, HDMI 5
    Direct hardware device without any conversions
hw:CARD=NVidia,DEV=12
    HDA NVidia, HDMI 6
    Direct hardware device without any conversions
plughw:CARD=NVidia,DEV=3
    HDA NVidia, HDMI 0
    Hardware device with all software conversions
plughw:CARD=NVidia,DEV=7
    HDA NVidia, HDMI 1
    Hardware device with all software conversions
plughw:CARD=NVidia,DEV=8
    HDA NVidia, HDMI 2
    Hardware device with all software conversions
plughw:CARD=NVidia,DEV=9
    HDA NVidia, HDMI 3
    Hardware device with all software conversions
plughw:CARD=NVidia,DEV=10
    HDA NVidia, HDMI 4
    Hardware device with all software conversions
plughw:CARD=NVidia,DEV=11
    HDA NVidia, HDMI 5
    Hardware device with all software conversions
plughw:CARD=NVidia,DEV=12
    HDA NVidia, HDMI 6
    Hardware device with all software conversions
usbstream:CARD=NVidia
    HDA NVidia
    USB Stream Output
________________
> arecord -L
default
    Playback/recording through the PulseAudio sound server
surround21
    2.1 Surround output to Front and Subwoofer speakers
surround40
    4.0 Surround output to Front and Rear speakers
surround41
    4.1 Surround output to Front, Rear and Subwoofer speakers
surround50
    5.0 Surround output to Front, Center and Rear speakers
surround51
    5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71
    7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
null
    Discard all samples (playback) or generate zero samples (capture)
samplerate
    Rate Converter Plugin Using Samplerate Library
speexrate
    Rate Converter Plugin Using Speex Resampler
jack
    JACK Audio Connection Kit
oss
    Open Sound System
pulse
    PulseAudio Sound Server
upmix
    Plugin for channel upmix (4,6,8)
vdownmix
    Plugin for channel downmix (stereo) with a simple spacialization
usbstream:CARD=NVidia
    HDA NVidia
    USB Stream Output
________________
> alsa_info_do
upload=true&script=true&cardinfo=
!!################################
!!ALSA Information Script v 0.4.64
!!################################

!!Script ran on: Mon Sep 27 17:08:56 UTC 2021


!!Linux Distribution
!!------------------

Linux Mint 20.2 Uma \n \l DISTRIB_ID=LinuxMint DISTRIB_DESCRIPTION="Linux Mint 20.2 Uma" NAME="Linux Mint" ID=linuxmint ID_LIKE=ubuntu PRETTY_NAME="Linux Mint 20.2" HOME_URL="https://www.linuxmint.com/" SUPPORT_URL="https://forums.linuxmint.com/" BUG_REPORT_URL="http://linuxmint-troubleshooting-guide.readthedocs.io/en/latest/" PRIVACY_POLICY_URL="https://www.linuxmint.com/" UBUNTU_CODENAME=focal


!!DMI Information
!!---------------

Manufacturer:      Dell Inc.
Product Name:      Precision 5760
Product Version:   
Firmware Version:  1.4.1
Board Vendor:      Dell Inc.
Board Name:        0T7J1J


!!ACPI Device Status Information
!!---------------

/sys/bus/acpi/devices/ACPI0003:00/status 	 15
/sys/bus/acpi/devices/ACPI000C:00/status 	 15
/sys/bus/acpi/devices/ACPI000E:00/status 	 15
/sys/bus/acpi/devices/DELL0A5E:00/status 	 15
/sys/bus/acpi/devices/DLB26390:00/status 	 15
/sys/bus/acpi/devices/DLLK0A5E:00/status 	 15
/sys/bus/acpi/devices/INT33A1:00/status 	 15
/sys/bus/acpi/devices/INT3403:00/status 	 15
/sys/bus/acpi/devices/INT3403:01/status 	 15
/sys/bus/acpi/devices/INT3403:02/status 	 15
/sys/bus/acpi/devices/INT3403:03/status 	 15
/sys/bus/acpi/devices/INT3403:04/status 	 15
/sys/bus/acpi/devices/INT3403:05/status 	 15
/sys/bus/acpi/devices/INT340E:00/status 	 15
/sys/bus/acpi/devices/INT34C6:00/status 	 15
/sys/bus/acpi/devices/INT3F0D:00/status 	 15
/sys/bus/acpi/devices/INTC1040:00/status 	 15
/sys/bus/acpi/devices/INTC1051:00/status 	 15
/sys/bus/acpi/devices/LNXPOWER:00/status 	 1
/sys/bus/acpi/devices/LNXPOWER:02/status 	 1
/sys/bus/acpi/devices/LNXPOWER:03/status 	 1
/sys/bus/acpi/devices/LNXPOWER:04/status 	 1
/sys/bus/acpi/devices/LNXPOWER:05/status 	 1
/sys/bus/acpi/devices/LNXPOWER:06/status 	 1
/sys/bus/acpi/devices/LNXPOWER:07/status 	 1
/sys/bus/acpi/devices/LNXPOWER:08/status 	 1
/sys/bus/acpi/devices/LNXPOWER:0b/status 	 1
/sys/bus/acpi/devices/LNXVIDEO:00/status 	 15
/sys/bus/acpi/devices/NVDA0820:00/status 	 15
/sys/bus/acpi/devices/PNP0103:00/status 	 15
/sys/bus/acpi/devices/PNP0C02:02/status 	 11
/sys/bus/acpi/devices/PNP0C02:04/status 	 11
/sys/bus/acpi/devices/PNP0C04:00/status 	 31
/sys/bus/acpi/devices/PNP0C09:00/status 	 15
/sys/bus/acpi/devices/PNP0C0A:00/status 	 31
/sys/bus/acpi/devices/PRP00001:00/status 	 11
/sys/bus/acpi/devices/PRP00001:01/status 	 11
/sys/bus/acpi/devices/SONY362A:01/status 	 15
/sys/bus/acpi/devices/STM0125:00/status 	 15
/sys/bus/acpi/devices/USBC000:00/status 	 15
/sys/bus/acpi/devices/device:0f/status 	 15
/sys/bus/acpi/devices/device:6b/status 	 15
/sys/bus/acpi/devices/device:8e/status 	 15
/sys/bus/acpi/devices/device:8f/status 	 15
/sys/bus/acpi/devices/device:90/status 	 15
/sys/bus/acpi/devices/device:92/status 	 15
/sys/bus/acpi/devices/device:93/status 	 15
/sys/bus/acpi/devices/device:94/status 	 15
/sys/bus/acpi/devices/device:c4/status 	 15
/sys/bus/acpi/devices/device:cb/status 	 15
/sys/bus/acpi/devices/device:cc/status 	 15
/sys/bus/acpi/devices/device:cd/status 	 15
/sys/bus/acpi/devices/device:cf/status 	 15
/sys/bus/acpi/devices/device:d1/status 	 15
/sys/bus/acpi/devices/device:d3/status 	 15


!!Kernel Information
!!------------------

Kernel release:    5.11.0-36-generic
Operating System:  GNU/Linux
Architecture:      x86_64
Processor:         x86_64
SMP Enabled:       Yes


!!ALSA Version
!!------------

Driver version:     k5.11.0-36-generic
Library version:    
Utilities version:  1.2.2


!!Loaded ALSA modules
!!-------------------

snd_hda_intel


!!Sound Servers on this system
!!----------------------------

Pulseaudio:
      Installed - Yes (/usr/bin/pulseaudio)
      Running - Yes


!!Soundcards recognised by ALSA
!!-----------------------------

 0 [NVidia         ]: HDA-Intel - HDA NVidia
                      HDA NVidia at 0xac000000 irq 17


!!PCI Soundcards installed in the system
!!--------------------------------------

0000:00:1f.3 Multimedia audio controller [0401]: Intel Corporation Device [8086:43c8] (rev 11)
	Subsystem: Dell Device [1028:0a5e]
0000:01:00.1 Audio device [0403]: NVIDIA Corporation Device [10de:228b] (rev a1)
	Subsystem: Dell Device [1028:0a5e]


!!Modprobe options (Sound related)
!!--------------------------------

snd_hda_intel: probe_only=0,1
snd_pcsp: index=-2
snd_usb_audio: index=-2
snd_atiixp_modem: index=-2
snd_intel8x0m: index=-2
snd_via82xx_modem: index=-2
snd_atiixp_modem: index=-2
snd_intel8x0m: index=-2
snd_via82xx_modem: index=-2
snd_usb_audio: index=-2
snd_usb_caiaq: index=-2
snd_usb_ua101: index=-2
snd_usb_us122l: index=-2
snd_usb_usx2y: index=-2
snd_cmipci: mpu_port=0x330 fm_port=0x388
snd_pcsp: index=-2
snd_usb_audio: index=-2
snd_hda_intel: probe_mask=1


!!Loaded sound module options
!!---------------------------

!!Module: snd_hda_intel
	align_buffer_size : -1
	bdl_pos_adj : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	beep_mode : N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N,N
	dmic_detect : Y
	enable : Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y
	enable_msi : -1
	id : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	index : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	jackpoll_ms : 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	model : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	patch : (null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)
	pm_blacklist : Y
	position_fix : -1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	power_save : 1
	power_save_controller : Y
	probe_mask : 1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1
	probe_only : 0,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
	single_cmd : -1
	snoop : -1


!!HDA-Intel Codec information
!!---------------------------
--startcollapse--

Codec: Nvidia GPU 9e HDMI/DP
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10de009e
Subsystem Id: 0x10280a5e
Revision Id: 0x100100
No Modem Function Group found
Default PCM:
    rates [0x0]:
    bits [0x0]:
    formats [0x0]:
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
  Power states:  D0 D1 D2 D3 CLKSTOP EPSS
  Power: setting=D0, actual=D0
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x04 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
  Pincap 0x09000094: OUT Detect HBR HDMI DP
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x00:
  Unsolicited: tag=01, enabled=1
  Devices: 4
     Dev 00: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
     Dev 01: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
     Dev 02: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
    *Dev 03: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
  Connection: 4
     0x08* 0x09 0x0a 0x0b
Node 0x05 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
  Pincap 0x09000094: OUT Detect HBR HDMI DP
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x00:
  Unsolicited: tag=05, enabled=1
  Devices: 4
     Dev 00: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
     Dev 01: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
     Dev 02: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
    *Dev 03: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
  Connection: 4
     0x08* 0x09 0x0a 0x0b
Node 0x06 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
  Pincap 0x09000094: OUT Detect HBR HDMI DP
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x00:
  Unsolicited: tag=09, enabled=1
  Devices: 4
     Dev 00: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
     Dev 01: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
     Dev 02: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
    *Dev 03: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
  Connection: 4
     0x08* 0x09 0x0a 0x0b
Node 0x07 [Pin Complex] wcaps 0x407381: 8-Channels Digital CP
  Pincap 0x09000094: OUT Detect HBR HDMI DP
  Pin Default 0x185600f0: [Jack] Digital Out at Int HDMI
    Conn = Digital, Color = Unknown
    DefAssociation = 0xf, Sequence = 0x0
  Pin-ctls: 0x00:
  Unsolicited: tag=0d, enabled=1
  Devices: 4
     Dev 00: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
     Dev 01: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
     Dev 02: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
    *Dev 03: PD = 0, ELDV = 0, IA = 0, Connections [ 0x08* 0x09 0x0a 0x0b ]
  Connection: 4
     0x08* 0x09 0x0a 0x0b
Node 0x08 [Audio Output] wcaps 0x62b1: 8-Channels Digital Stripe
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Unsolicited: tag=00, enabled=0
Node 0x09 [Audio Output] wcaps 0x62b1: 8-Channels Digital Stripe
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Unsolicited: tag=00, enabled=0
Node 0x0a [Audio Output] wcaps 0x62b1: 8-Channels Digital Stripe
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Unsolicited: tag=00, enabled=0
Node 0x0b [Audio Output] wcaps 0x62b1: 8-Channels Digital Stripe
  Converter: stream=0, channel=0
  Digital:
  Digital category: 0x0
  IEC Coding Type: 0x0
  PCM:
    rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
    bits [0xe]: 16 20 24
    formats [0x5]: PCM AC3
  Unsolicited: tag=00, enabled=0
--endcollapse--


!!ALSA Device nodes
!!-----------------

crw-rw----+ 1 root audio 116, 10 Sep 26 14:23 /dev/snd/controlC0
crw-rw----+ 1 root audio 116,  9 Sep 26 14:23 /dev/snd/hwC0D0
crw-rw----+ 1 root audio 116,  6 Sep 26 15:51 /dev/snd/pcmC0D10p
crw-rw----+ 1 root audio 116,  7 Sep 26 15:51 /dev/snd/pcmC0D11p
crw-rw----+ 1 root audio 116,  8 Sep 26 15:51 /dev/snd/pcmC0D12p
crw-rw----+ 1 root audio 116,  2 Sep 26 15:51 /dev/snd/pcmC0D3p
crw-rw----+ 1 root audio 116,  3 Sep 26 15:51 /dev/snd/pcmC0D7p
crw-rw----+ 1 root audio 116,  4 Sep 26 15:51 /dev/snd/pcmC0D8p
crw-rw----+ 1 root audio 116,  5 Sep 26 15:51 /dev/snd/pcmC0D9p
crw-rw----+ 1 root audio 116,  1 Sep 26 14:23 /dev/snd/seq
crw-rw----+ 1 root audio 116, 33 Sep 26 14:23 /dev/snd/timer

/dev/snd/by-path:
total 0
drwxr-xr-x 2 root root  60 Sep 26 14:23 .
drwxr-xr-x 3 root root 280 Sep 26 14:23 ..
lrwxrwxrwx 1 root root  12 Sep 26 14:23 pci-0000:01:00.1 -> ../controlC0


!!Aplay/Arecord output
!!--------------------

APLAY

**** List of PLAYBACK Hardware Devices ****
card 0: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 7: HDMI 1 [HDMI 1]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 8: HDMI 2 [HDMI 2]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 9: HDMI 3 [HDMI 3]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 10: HDMI 4 [HDMI 4]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 11: HDMI 5 [HDMI 5]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 12: HDMI 6 [HDMI 6]
  Subdevices: 1/1
  Subdevice #0: subdevice #0

ARECORD

**** List of CAPTURE Hardware Devices ****

!!Amixer output
!!-------------

!!-------Mixer controls for card NVidia

Card hw:0 'NVidia'/'HDA NVidia at 0xac000000 irq 17'
  Mixer name	: 'Nvidia GPU 9e HDMI/DP'
  Components	: 'HDA:10de009e,10280a5e,00100100'
  Controls      : 49
  Simple ctrls  : 7
Simple mixer control 'IEC958',0
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'IEC958',1
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'IEC958',2
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'IEC958',3
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'IEC958',4
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'IEC958',5
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]
Simple mixer control 'IEC958',6
  Capabilities: pswitch pswitch-joined
  Playback channels: Mono
  Mono: Playback [on]





!!All Loaded Modules
!!------------------

ac97_bus
acpi_pad
acpi_tad
acpi_thermal_rel
aesni_intel
af_alg
algif_hash
algif_skcipher
autofs4
binfmt_misc
blake2b_generic
bluetooth
bnep
btbcm
btintel
btqca
btrfs
btrtl
btusb
ccm
cec
cfg80211
cmac
coretemp
crc32_pclmul
crct10dif_pclmul
cros_ec
cros_ec_ishtp
cryptd
crypto_simd
dcdbas
dell_laptop
dell_rbtn
dell_smbios
dell_wmi
dell_wmi_descriptor
dm_crypt
dm_log
dm_mirror
dm_region_hash
drm
drm_kms_helper
ecc
ecdh_generic
ee1004
efi_pstore
fb_sys_fops
ghash_clmulni_intel
glue_helper
hci_uart
hfs
hfsplus
hid
hid_generic
hid_multitouch
hid_sensor_als
hid_sensor_custom
hid_sensor_hub
hid_sensor_iio_common
hid_sensor_trigger
i2c_algo_bit
i2c_hid
i2c_i801
i2c_smbus
i915
idma64
industrialio
industrialio_triggered_buffer
input_leds
int3400_thermal
int3403_thermal
int340x_thermal_zone
intel_cstate
intel_hid
intel_ish_ipc
intel_ishtp
intel_ishtp_hid
intel_ishtp_loader
intel_lpss
intel_lpss_pci
intel_pmt
intel_pmt_class
intel_pmt_telemetry
intel_powerclamp
intel_rapl_common
intel_rapl_msr
intel_soc_dts_iosf
ip_tables
iwlmvm
iwlwifi
jfs
joydev
kfifo_buf
kvm
kvm_intel
ledtrig_audio
libarc4
libcrc32c
lp
mac80211
mac_hid
mc
mei
mei_hdcp
mei_me
minix
msdos
msr
nls_iso8859_1
ntfs
nvidia
nvidia_drm
nvidia_modeset
nvidia_uvm
nvme
nvme_core
parport
parport_pc
pinctrl_tigerlake
ppdev
processor_thermal_device
processor_thermal_mbox
processor_thermal_rapl
processor_thermal_rfim
qnx4
raid6_pq
rc_core
regmap_sdw
rfcomm
rtsx_pci
rtsx_pci_sdmmc
sch_fq_codel
serio_raw
snd
snd_compress
snd_hda_codec
snd_hda_codec_hdmi
snd_hda_core
snd_hda_ext_core
snd_hda_intel
snd_hwdep
snd_intel_dspcfg
snd_pcm
snd_pcm_dmaengine
snd_rawmidi
snd_seq
snd_seq_device
snd_seq_midi
snd_seq_midi_event
snd_soc_acpi
snd_soc_acpi_intel_match
snd_soc_core
snd_soc_dmic
snd_soc_hdac_hda
snd_soc_rt1308_sdw
snd_soc_rt711
snd_soc_rt715
snd_sof
snd_sof_intel_byt
snd_sof_intel_hda
snd_sof_intel_hda_common
snd_sof_intel_ipc
snd_sof_pci
snd_sof_xtensa_dsp
snd_timer
soundcore
soundwire_bus
soundwire_cadence
soundwire_generic_allocation
soundwire_intel
sparse_keymap
syscopyarea
sysfillrect
sysimgblt
thunderbolt
typec
typec_ucsi
ucsi_acpi
ufs
uhid
uvcvideo
video
videobuf2_common
videobuf2_memops
videobuf2_v4l2
videobuf2_vmalloc
videodev
virt_dma
vmd
vmw_vmci
vmw_vsock_vmci_transport
vsock
wmi
wmi_bmof
x86_pkg_temp_thermal
x_tables
xfs
xhci_pci
xhci_pci_renesas
xor


!!Sysfs Files
!!-----------

/sys/class/sound/hwC0D0/init_pin_configs:
0x04 0x185600f0
0x05 0x185600f0
0x06 0x185600f0
0x07 0x185600f0

/sys/class/sound/hwC0D0/driver_pin_configs:

/sys/class/sound/hwC0D0/user_pin_configs:

/sys/class/sound/hwC0D0/init_verbs:

/sys/class/sound/hwC0D0/hints:


!!ALSA/HDA dmesg
!!--------------

[    0.174206] ACPI: Added _OSI(Linux-Dell-Video)
[    0.174206] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.174206] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
--
[   14.045213] iwlwifi 0000:00:14.3: Detected Intel(R) Wi-Fi 6 AX201 160MHz, REV=0x354
[   14.046686] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100
[   14.046806] snd_hda_intel 0000:00:1f.3: SoundWire enabled on CannonLake+ platform, using SOF driver
[   14.068387] dell_smm_hwmon: unable to get SMM Dell signature
--
[   14.349825] nvidia 0000:01:00.0: enabling device (0006 -> 0007)
[   14.349890] snd_hda_intel 0000:01:00.1: enabling device (0000 -> 0002)
[   14.350008] nvidia 0000:01:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=none
[   14.350239] snd_hda_intel 0000:01:00.1: Disabling MSI
[   14.350251] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[   14.563877] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  470.63.01  Tue Aug  3 20:44:16 UTC 2021
--
[   14.589545] [drm] [nvidia-drm] [GPU ID 0x00000100] Loading driver
[   14.602626] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card0/input13
[   14.606115] audit: type=1400 audit(1632680602.915:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=966 comm="apparmor_parser"
--
[   14.622769] sof-audio-pci 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[   14.626600] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card0/input14
[   14.626635] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card0/input15
[   14.626672] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card0/input16
[   14.626710] input: HDA NVidia HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card0/input17
[   14.626751] input: HDA NVidia HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card0/input18
[   14.626804] input: HDA NVidia HDMI/DP,pcm=12 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card0/input19
[   14.628138] uvcvideo: Found UVC 1.00 device Integrated_Webcam_HD (0c45:6d1b)
--
[   14.636747] ACPI Warning: \_SB.PC00.PEG1.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20201113/nsarguments-61)
[   14.641366] sof-audio-pci 0000:00:1f.3: hda codecs found, mask 4
[   14.659675] input: DELL0A5E:00 04F3:311C Mouse as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-11/i2c-DELL0A5E:00/0018:04F3:311C.0001/input/input21
Attachments
Audio Script Output.txt.tar.gz
(12.51 KiB) Downloaded 26 times
User avatar
MrEen
Level 23
Level 23
Posts: 18345
Joined: Mon Jun 12, 2017 8:39 pm

Re: No Sound - Dell Precision 5760

Post by MrEen »

Strange. There should be plenty more after this line:

Code: Select all

[   14.641366] sof-audio-pci 0000:00:1f.3: hda codecs found, mask 4
That's the second last line of the entire output.

You added a couple of probe options to a file or files in /etc/modprobe.d/:
snd_hda_intel: probe_only=0,1
snd_pcsp: index=-2
snd_usb_audio: index=-2
snd_atiixp_modem: index=-2
snd_intel8x0m: index=-2
snd_via82xx_modem: index=-2
snd_atiixp_modem: index=-2
snd_intel8x0m: index=-2
snd_via82xx_modem: index=-2
snd_usb_audio: index=-2
snd_usb_caiaq: index=-2
snd_usb_ua101: index=-2
snd_usb_us122l: index=-2
snd_usb_usx2y: index=-2
snd_cmipci: mpu_port=0x330 fm_port=0x388
snd_pcsp: index=-2
snd_usb_audio: index=-2
snd_hda_intel: probe_mask=1
Please remove both of those edits then reboot and run this again:

Code: Select all

curl https://gitlab.freedesktop.org/pulseaudio/pulseaudio/raw/master/src/utils/pa-info?inline=false | bash | nc termbin.com 9999
alchez3
Level 1
Level 1
Posts: 5
Joined: Mon Sep 20, 2021 4:29 pm

Re: No Sound - Dell Precision 5760

Post by alchez3 »

Wanted thank you for your help!
I installed these updates today and after reboot sound is working.
2021-09-28_15-18.png
User avatar
MrEen
Level 23
Level 23
Posts: 18345
Joined: Mon Jun 12, 2017 8:39 pm

Re: Solved - No Sound - Dell Precision 5760

Post by MrEen »

That's great! I'm glad your sound is fixed. :D
Locked

Return to “Hardware Support”