Canon Pixma MG3660

Forum rules
Before you post please read this
Post Reply
EdQld
Level 2
Level 2
Posts: 88
Joined: Fri May 01, 2009 5:35 am

Canon Pixma MG3660

Post by EdQld » Mon Jan 09, 2017 4:03 am

I just purchased a Canon Maxima MG3660 and tried to connect it to my Linux Mint PC. The printer connects via WiFi but of course there are no instructions for Linux :-(

When I went to "Add Printer" I could not find the Printer so I tried finding it via the supplied MAC Address but although there are heaps of Canon models in the Data Base, this one of course is not included

Any ideas how I might get this connected to my Linux Mint PC via WiFi? (easy step by step would be appreciated, I have old-timers disease)

Thanks

pdc_2
Level 8
Level 8
Posts: 2419
Joined: Mon May 11, 2009 1:21 am

Re: Canon Pixma MG3660

Post by pdc_2 » Mon Jan 09, 2017 4:12 am

so Canon supply debian package drivers; Mint uses ubuntu; that uses debian; so all is good

go here http://support-asia.canon-asia.com/cont ... 90202.html and download cnijfilter2-5.20-1-deb.tar.gz and maybe also click the "yes, this was helpful" button at the bottom of the page ......

either use a terminal; or open your Downloads folder from the desktop:

terminal commands are
cd Downloads
tar -xzvf cnijfilter2-5.20-1-deb.tar.gz
cd cnijfilter2-5.20-1-deb
./install.sh
and that should install the drivers for you

_____________

Canon provide ScanGearMP to run the scanner

get it from here http://support-asia.canon-asia.com/cont ... 90502.html and get scangearmp2-3.20-1-deb.tar.gz .....the structure of the commands are the same as above; shall I spell it all out .. happy to if needed

..... the key thing is to run it first off, type
scangearmp2
in the terminal ........ let me know if it works and we can set up a short-cut to load it for you .......

EdQld
Level 2
Level 2
Posts: 88
Joined: Fri May 01, 2009 5:35 am

Resolved: Canon Pixma MG3660

Post by EdQld » Mon Jan 09, 2017 4:38 am

Thank you for your help, unfortunately following the fist part of your suggestions ended up with a error message "Could not detect the target printer" :(

I switched the power off & back on for the Printer and tried again, but still this error message
The WiFi light on the Printer is solid on

ADDIT
OK, I connected the Printer to my Router via a WIN PC and then tried to "Add Printer" again on my Mint PC, this time it found the Printer and the right version :D
Not sure if the Terminal commands you suggested also played a part, but I'm just happy to get it working :D

Thanks very much for you help

ADDIT
Simple Scan could not detect the Canon but I still have an out of ink HP Printer connected to the Network that I can use with that and Fax the occasional document

pdc_2
Level 8
Level 8
Posts: 2419
Joined: Mon May 11, 2009 1:21 am

Re: Canon Pixma MG3660

Post by pdc_2 » Mon Jan 09, 2017 2:55 pm

glad the printer side is working;

you can use Simple Scan if you install ScanGearMP; it is a different programme: so if you install ScanGearMP, you need to test it works with

Code: Select all

[color=#FF0000]scangear2[/color]
in a terminal, and if it works, you can set up a shortcut: do you use Mate?

EdQld
Level 2
Level 2
Posts: 88
Joined: Fri May 01, 2009 5:35 am

Re: Canon Pixma MG3660

Post by EdQld » Mon Jan 09, 2017 8:21 pm

Thanks again for your help, Ok, Step1 got the printer working so I thought I might as well try the next step for the Scanner 8)

Yes I'm using Mate Mint 17.3

I downloaded the scangearmp2-3.20-1-deb.tar.gz file and followed you format for the first step eg "tar -xzvf scangearmp2-3.20-1-deb.tar.gz" ect

When I had finished, I tried the following Terminal Commands, both in a new Terminal & following "cd scangearmp2-3.20-1-deb"
scangear2 > OK from Preview it looks like those parameters are just to change the colour of the command in the Forum
scangear2
they produced error messages: "No such file or directory" or "Command not found"

So where do I go from here?

Thanks again for your support :D

ADDIT
Just reviewd all the commands again and noticed the deb file was scangearmp2, not scangear2, so I tried that as a Terminal Command and it brought up a Scanner for the Canon Printer which I was able to successfully use to scan a doc, could you show me how to create that short-cut?
Simple Scan however only see the original HP Printer and can't find the Canon Printer

pdc_2
Level 8
Level 8
Posts: 2419
Joined: Mon May 11, 2009 1:21 am

Re: Canon Pixma MG3660

Post by pdc_2 » Tue Jan 10, 2017 2:36 am

apologies for my error: well done to troubleshoot and sort it all!! good work

if you are using Mate, right-click on the bottom bar; select ADD TO PANEL; select the top offering: CUSTOM APPLICATION LAUNCHER: click the ADD button; name can be whatever you like: COMMAND must be

Code: Select all

scangearmp2
.....which you successfully worked out!!! ....... and you can change the icons etc but that gives you a working shortcut ............... let us know how it goes .......

EdQld
Level 2
Level 2
Posts: 88
Joined: Fri May 01, 2009 5:35 am

Re: Canon Pixma MG3660

Post by EdQld » Tue Jan 10, 2017 3:24 am

Brilliant, worked a treat, thank you so very much, really appreciate you help :D

pdc_2
Level 8
Level 8
Posts: 2419
Joined: Mon May 11, 2009 1:21 am

Re: Canon Pixma MG3660

Post by pdc_2 » Tue Jan 10, 2017 3:29 am

great! Enjoy!

Post Reply

Return to “Printers & Scanners”