It could be very trivial question, but I can't find it ...
In my try there is no icon for wireless network any more. I'm not sure if I've done anything wrong (don't remember doing anything with wireless). I guess it could be gone after some system updated ...
Wi-Fi is working and I can connect to the networks that has been remembered before, but I can't connect to any new one, as I don't know how to get to this configuration of wi-fi.
Could anyone help me how to get my icon back, or how to run the configuration of wi-fi from terminal / menu panel ?
Regards,
Łukasz Konkol
Code: Select all
konki@Konki-ThinkPad-T520 ~ $ sudo /usr/lib/linuxmint/mintWifi/mintWifi.py
[sudo] password for konki:
-------------------------
* I. scanning WIFI PCI devices...
-- Intel Corporation Centrino Advanced-N 6205 (rev 34)
==> PCI ID = 8086:0085 (rev 34)
-------------------------
* II. querying ndiswrapper...
-------------------------
* III. querying iwconfig...
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11abgn ESSID:"T2_Internet_Access"
Mode:Managed Frequency:5.18 GHz Access Point: 08:D0:9F:22:57:1D
Bit Rate=144.4 Mb/s Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=69/70 Signal level=-41 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:17885 Invalid misc:57 Missed beacon:0
-------------------------
* IV. querying ifconfig...
eth0 Link encap:Ethernet HWaddr f0:de:f1:55:88:7a
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:20 Memory:f3a00000-f3a20000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4292 errors:0 dropped:0 overruns:0 frame:0
TX packets:4292 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:482441 (482.4 KB) TX bytes:482441 (482.4 KB)
wlan0 Link encap:Ethernet HWaddr a0:88:b4:13:7b:1c
inet addr:90.132.131.87 Bcast:90.132.131.255 Mask:255.255.254.0
inet6 addr: 2a00:801:1:a:a484:1eba:ce53:93b1/64 Scope:Global
inet6 addr: 2a00:801:1:a:a288:b4ff:fe13:7b1c/64 Scope:Global
inet6 addr: fe80::a288:b4ff:fe13:7b1c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:123970 errors:0 dropped:0 overruns:0 frame:0
TX packets:36883 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:67867408 (67.8 MB) TX bytes:5266955 (5.2 MB)
-------------------------
* V. querying DHCP...
Rather than invoking init scripts through /etc/init.d, use the service(8)
utility, e.g. service smbd reload
Since the script you are attempting to invoke has been converted to an
Upstart job, you may also use the reload(8) utility, e.g. reload smbd
RTNETLINK answers: File exists
-------------------------
* VI. querying nslookup google.com...
Server: 130.244.127.161
Address: 130.244.127.161#53
Non-authoritative answer:
Name: google.com
Address: 173.194.32.41
Name: google.com
Address: 173.194.32.46
Name: google.com
Address: 173.194.32.32
Name: google.com
Address: 173.194.32.33
Name: google.com
Address: 173.194.32.34
Name: google.com
Address: 173.194.32.35
Name: google.com
Address: 173.194.32.36
Name: google.com
Address: 173.194.32.37
Name: google.com
Address: 173.194.32.38
Name: google.com
Address: 173.194.32.39
Name: google.com
Address: 173.194.32.40
