As a newbie I only can post here, so apologies if not posted under Network.
I'm upgrading my network to 10Gb and trying to get hand full boxes on those ports. So you better understand, I'm using two SFP+ Aruba S2500 switches. That net six 10Gb ports for my servers/workstations, as two are used to uplink the switches.
As all new implementation the learning curve is tough and this one is not an exception...
Currently I have:
- FreeBSD 11.2 server/Chelsio T320 - working
- FreeNAS 11.1 serverChelsio T320 - working
- Windows 10 workstation/Mellanox - working
- ESXi 6.5 T320 - No Go (waiting on a T5 to re-try)
and the most important to me:
- Linux Mint 19 workstation/Chelsio T320
Did a fresh install of LM 19 to remove any of previous tests/changes I'd done. Card shows as expected:
Code: Select all
mello@olinda:~$ dmesg | grep -i Chelsio
[ 0.927537] cxgb3: Chelsio T3 Network Driver - version 1.1.5-ko
[ 1.269054] cxgb3 0000:06:00.0 eth0: Chelsio T320 10GBASE-R NIC (rev 4) PCI Express x1 MSI-X
[ 1.269056] cxgb3 0000:06:00.0 eth1: Chelsio T320 10GBASE-R NIC (rev 4) PCI Express x1 MSI-X
Code: Select all
mello@olinda:~$ ifconfig rename2
rename2: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.10.10.60 netmask 255.255.255.0 broadcast 10.10.10.255
inet6 fe80::207:43ff:fe06:b659 prefixlen 64 scopeid 0x20<link>
ether 00:07:43:06:b6:59 txqueuelen 1000 (Ethernet)
RX packets 6333088 bytes 4122670256 (4.1 GB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8833892 bytes 10859459898 (10.8 GB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 16 memory 0xf7881000-f7881fff
Code: Select all
root@bhyve:~ # iperf -s
------------------------------------------------------------
Server listening on TCP port 5001
TCP window size: 64.0 KByte (default)
------------------------------------------------------------
[ 4] local 10.10.10.152 port 5001 connected with 10.10.10.60 port 56146
[ ID] Interval Transfer Bandwidth
[ 4] 0.0-10.0 sec 1.89 GBytes 1.62 Gbits/sec
Code: Select all
mello@olinda:~$ sudo ifconfig rename2 mtu 9000
mello@olinda:~$ iperf -c bhyve
------------------------------------------------------------
Client connecting to bhyve, TCP port 5001
TCP window size: 325 KByte (default)
------------------------------------------------------------
[ 3] local 10.10.10.60 port 56712 connected with 10.10.10.152 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.2 sec 326 KBytes 261 Kbits/sec
Code: Select all
mello@olinda:~$ iperf -s
------------------------------------------------------------
Server listening on TCP port 5001
TCP window size: 85.3 KByte (default)
------------------------------------------------------------
[ 4] local 10.10.10.60 port 5001 connected with 10.10.10.60 port 46248
[ ID] Interval Transfer Bandwidth
[ 4] 0.0-10.0 sec 28.1 GBytes 24.1 Gbits/sec
Thanks,
Al