Enabling S3 Trio as a second adapter

Screen resolution, 3D Acceleration, nVidia, ATI
Forum rules
Before you post please read this
Post Reply
mctom
Level 2
Level 2
Posts: 72
Joined: Wed Jan 07, 2015 2:37 pm
Location: Gdańsk, Poland

Enabling S3 Trio as a second adapter

Post by mctom »

Hello!
Just as stated in the subject, I've shoved a vintage S3 Trio to my system. I want to connect a projector to it and use it like a third monitor.
The trouble is, Linux Mint 17.2 Cinnamon is only partially aware of my intentions. Although some commands do acknowledge the presence of my extra GPU, I can't see how can I make use of my card because the "Display" tool doesn't see anything except of my two monitors plugged into my primary GPU.

Here are some command outputs (essential parts only):

sudo lspci -vvvv

Code: Select all

05:01.0 VGA compatible controller: S3 Graphics Ltd. 86c764/765 [Trio32/64/64V+] (rev 53) (prog-if 00 [VGA controller])
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at f0000000 (32-bit, non-prefetchable) [disabled] [size=64M]
	Expansion ROM at f4000000 [disabled] [size=64K]
inxi -Fxxx

Code: Select all

Graphics:  Card-1: Advanced Micro Devices [AMD/ATI] Cape Verde XT [Radeon HD 7770/8760 / R7 250X] bus-ID: 01:00.0 chip-ID: 1002:683d 
           Card-2: S3 Graphics 86c764/765 [Trio32/64/64V+] bus-ID: 05:01.0 chip-ID: 5333:8811 
           X.Org: 1.15.1 drivers: ati,fglrx (unloaded: fbdev,vesa,radeon) Resolution: 1280x1024@60.0hz, 1920x1080@59.9hz 
           GLX Renderer: AMD Radeon HD 7700 Series GLX Version: 4.4.13374 - CPC 13.35.1005 Direct Rendering: Yes
cat /var/log/gpu-manager.log

Code: Select all

Vendor/Device Id: 1002:683d
BusID "PCI:1@0:0:0"
Is boot vga? yes
Vendor/Device Id: 5333:8811
BusID "PCI:5@0:1:0"
Is boot vga? no
Error: can't access /sys/bus/pci/devices/0000:05:01.0/driver
The device is not bound to any driver. Skipping...
last cards number = 1
Hmm, so I figure I must pick a driver for my card. How do I do that?
Thanks for your help in advance!
I am an inexperienced linux user, so please don't hesitate to correct me if I am wrong. Thank you!

Punk ain't no religious cult, Punk means thinking for yourself!
mctom
Level 2
Level 2
Posts: 72
Joined: Wed Jan 07, 2015 2:37 pm
Location: Gdańsk, Poland

Re: Enabling S3 Trio as a second adapter

Post by mctom »

I have figured out some solutions, but none of them seems to work.

- I have read that the "xserver-xorg-video-s3" package is essential, but it is already installed in Mint by default
- I have removed "s3fg" from the kernel module blacklist,
- Many people suggest modifying xorg.conf to point a driver to a device, but I read on this forum that xorg.conf is obsolete and should not be used. Then what?

The output of the commands has not changed. Of course I did a full reset after each step.

Any ideas? Guyyys..

EDIT: I found this in dmesg:

Code: Select all

[    6.010906] s3fb 0000:05:01.0: ignoring secondary device
Does that mean I can't use secondary VGA card by design of the system? :/
I am an inexperienced linux user, so please don't hesitate to correct me if I am wrong. Thank you!

Punk ain't no religious cult, Punk means thinking for yourself!
Post Reply

Return to “Graphics Cards & Monitors”